Key takeaways
- New and fully replaced wet heating systems in England should be sized to run at a maximum flow temperature of 55°C or lower[1].
- Radiator output falls steeply as the water gets cooler, so a radiator that was generous at boiler temperatures can be short at 45°C.
- Size from a room-by-room heat loss, not from the old radiators; from 24 March 2027 the guidance says so in terms for new systems[2].
- Quote radiator upgrades room by room, with the target flow temperature stated, so the customer can see what each change buys.
Why radiator sizing has become a selling point
For decades, radiators in British homes were sized for boilers running hot, and most systems were oversized enough that nobody noticed small errors. That margin is shrinking. Condensing boilers are now the norm, with 63% of homes in England on a condensing combi and 19% on a condensing boiler that is not a combi in 2024[3], and they work best with cooler return water. Heat pumps need lower flow temperatures still, and government wants more than 450,000 heat pump installations a year by 2030[4]. The Boiler Upgrade Scheme had already received 160,874 voucher applications by the end of September 2026[5].
- 2001
- 2024
Source: Ministry of Housing, Communities and Local Government (GOV.UK), 2024[3]
Show the data
| Item | 2001 | 2024 |
|---|---|---|
| Condensing combination boiler | 2% | 63% |
| Condensing boiler (not combi) | 1% | 19% |
Each of those jobs raises the same question: will the radiators keep the rooms warm at a lower water temperature? Firms that can answer it with numbers, room by room, win both the boiler customers who want lower bills and the heat pump customers who need it done right.
What Approved Document L requires
In England, Approved Document L says that where a wet heating system is newly installed, or fully replaced including the heat source, emitters and pipework, all parts of the system should be sized so it meets the heating needs of the dwelling at a maximum flow temperature of 55°C or lower[1]. Where that is not feasible, for example because there is not enough space for larger radiators, the system should be designed for the lowest flow temperature that still meets the heating needs[1]. Systems should be sized from a heat loss calculation and a sizing method that reflects the property, and should not be significantly oversized[1].
The 2026 edition, which takes effect in England on 24 March 2027, is more direct. It says a room-by-room heat loss calculation should be used when a new heating system including emitters is installed, a whole-dwelling calculation is appropriate when only the heating appliance is replaced, and sizing a replacement appliance from the output of the old one is not appropriate[2]. It points to BS EN 12831-1 for the heat loss calculation and to the BRE guide FB 59 on low-temperature domestic heating design[2].
Delta-T in plain words
A radiator's output depends on the difference between the average water temperature inside it and the air temperature in the room, usually written as delta-T. Catalogues quote output at one standard delta-T, and each manufacturer publishes correction factors or an exponent to convert that figure to other conditions. Check the rating conditions in the catalogue before you compare models, because not every supplier quotes on the same basis.
The relationship is not linear. Halving the delta-T cuts output by more than half, because a radiator also loses some of its convective draught as it cools. That is why a system that ran happily at high temperatures can leave the coldest rooms short when the flow temperature drops, and why simply turning down the boiler is not a design.
Example: correcting radiator output
Example (fictional, for illustration only): the factors below assume a radiator exponent of 1.3 and a room at 21°C. Real exponents vary by radiator type and manufacturer, so use their data for any quote.
| Mean water temperature | Delta-T | Share of catalogue output (Example) |
|---|---|---|
| 71°C | 50 | 1.00 |
| 65°C | 44 | 0.85 |
| 50°C | 29 | 0.49 |
| 45°C | 24 | 0.39 |
Example: a back bedroom needs 900W at the design condition. Its existing radiator is rated 1,500W at the catalogue delta-T. At a 45°C mean water temperature the Example factor is 0.39, so it delivers about 585W, well short. To meet 900W at that temperature the room needs about 2,310W of catalogue output, which might mean a larger double-panel radiator or two radiators. At a 50°C mean, the existing radiator gives about 735W, still short, so the decision is whether to upgrade this room or design the whole system slightly warmer.
Quoting a radiator upgrade
Measure every room
Dimensions, window and door sizes, wall and floor construction and any obvious insulation, recorded room by room.
Calculate room heat loss
Use a BS EN 12831-1 method or a recognised tool, with the design temperatures stated on the sheet.
Set the target flow temperature
For a full system replacement aim for 55°C or lower; for a heat pump, use the temperature the heat pump design needs.
Correct each radiator
Convert the existing radiator's catalogue output to the target conditions using the manufacturer's data and compare it with the room's heat loss.
Schedule the changes
List only the rooms that fall short, with the proposed radiator size and type for each.
Check pipework and controls
Confirm pipe sizes can carry the flow needed and fit thermostatic room controls where the boiler is being replaced.
Approved Document L expects thermostatic room controls in each room when a boiler is replaced in an existing dwelling, unless one of its exceptions applies[1]. Before fitting a new heat source, clean and flush the system and add inhibitor, preparing and commissioning to BS 7593[1]. New radiators on a dirty system will not stay efficient for long.
Pipework and flow rates
Lower flow temperatures usually come with smaller temperature drops across each radiator, which means more water has to move to deliver the same heat. Microbore runs that were fine at high temperatures can become the bottleneck. Check pipe sizes on the longest and highest-load circuits and include any pipe upgrades in the quote rather than discovering them on the day.
Balance the system once the new radiators are in. A well-sized radiator on an unbalanced system will still underperform, and the customer will judge the job by the coldest room, not by the calculation.
When bigger radiators are not the answer
Sometimes the room simply has no wall space for the radiator the calculation asks for. Before you design the whole house warmer to suit one room, look at the alternatives. Reducing the room's heat loss is often the cheapest fix: draught-proofing, loft insulation over that room or secondary glazing can bring the heat need down to what an achievable radiator delivers. In a kitchen or a ground-floor extension being renovated, underfloor heating may suit the low flow temperature better than any radiator.
Be honest when a room cannot reach the target without work the customer does not want. Record the compromise on the quote, such as a design flow temperature a few degrees higher, and explain what it means for efficiency. A customer who agreed to a known compromise rarely complains; one who discovers it in January usually does. For heat pump jobs, the room-by-room figures should come from a proper heat loss survey, so the radiator schedule and the heat pump size come from the same numbers.
Presenting the quote
Customers understand rooms, not watts. Lay the quote out as a room list: the room, its heat need, the existing radiator's output at the target temperature, and the proposed change. Mark rooms that already pass. A customer who sees that six of nine rooms are fine is more likely to accept the three changes than one who receives a single total for a whole-house swap.
- State the target flow temperature and the design outdoor temperature on the quote.
- Show the existing and new outputs at that temperature, not catalogue figures.
- Offer options where space is tight: a taller or wider radiator, a higher-output type, or a slightly higher design flow temperature for that room.
- Note any pipework, valve and control changes separately.
- Avoid promising a specific bill saving; explain that lower flow temperatures let modern heat sources run more efficiently.
Mistakes that cost callbacks
- Assuming old radiators are oversized without checking: some are, some are not.
- Sizing from catalogue output at the standard delta-T instead of the corrected figure.
- Ignoring rooms with large windows, solid walls or extensions, which are usually the ones that fall short.
- Forgetting that a bathroom towel rail gives much less heat than a radiator of similar size.
- Not explaining that low-temperature systems warm rooms more gently and are best run for longer, steadier periods.
Write these into your survey sheet as prompts. They are cheap to check during the survey and expensive to fix once the customer has decorated around new radiators.
Frequently asked questions
Do all radiator replacements have to be sized for 55°C?
In England the 55°C guidance applies when a wet system is newly installed or fully replaced, including the heat source, emitters and pipework. Swapping one radiator is not a full replacement, but sizing for lower temperatures is still good practice.
Can I size radiators from the old ones?
No. Size from a room heat loss calculation. The 2026 edition of Approved Document L says sizing from the existing installation is not appropriate.
What is delta-T?
The difference between the average water temperature in the radiator and the room air temperature. Radiator output is quoted at a standard delta-T and must be corrected for other conditions.
Will bigger radiators reduce the customer's bills?
They let a condensing boiler or heat pump run at lower flow temperatures, which improves efficiency. Avoid promising a specific saving.
References
GOV.UK (Ministry of Housing, Communities and Local Government) (2023). Approved Document L, Volume 1: Dwellings (2021 edition incorporating 2023 amendments) (opens in a new tab) ↑
GOV.UK (Ministry of Housing, Communities and Local Government) (2026). Approved Document L, Volume 1: Dwellings (2026 edition) (opens in a new tab) ↑
Ministry of Housing, Communities and Local Government (GOV.UK) (2024). English Housing Survey 2024 to 2025: Chapter 2, energy efficiency (opens in a new tab) ↑
Department for Energy Security and Net Zero (GOV.UK) (2026). Warm Homes Plan (opens in a new tab) ↑
Department for Energy Security and Net Zero (2026). Boiler Upgrade Scheme (BUS) monthly statistics: England and Wales, September 2026 (opens in a new tab) ↑