Key takeaways
- A home built before 1970 may have lead pipes, and the owner is responsible for the supply pipe from the outside stop valve to the kitchen tap[1].
- The legal limit for lead in drinking water at the tap in England is 10 micrograms per litre[2].
- Infants, including unborn babies, and children are at particular risk, so homes with young families are the priority[1].
- 31% of privately rented homes in England were built before 1919[3], so landlords are a natural audience for lead surveys.
Why lead still turns up
Lead was a standard material for water service pipes for generations, and much of it is still in the ground. The Drinking Water Inspectorate says that if a home was built before 1970 it may have lead pipes[1]. Many have been replaced during refits, but a short section under the kitchen floor or a run between the boundary and the house is easily missed, and it is still carrying drinking water today.
Older homes are concentrated in particular tenures. In England, 31% of privately rented dwellings were built before 1919, against 20% of owner-occupied and 7% of social rented homes[3]. Pre-1919 homes are not the only ones with lead, but they are the most likely to have it somewhere in the supply.
Source: Ministry of Housing, Communities and Local Government (GOV.UK), 2025[3]
Show the data
| Item | Value |
|---|---|
| Owner-occupied | 20% |
| Private rented | 31% |
| Social rented | 7% |
Who owns which pipe
Customers almost always ask who pays, so start there. The water company owns the communication pipe from the main in the street to the stop valve outside the property. The owner is responsible for the supply pipe from that stop valve into the home and for all internal plumbing up to the kitchen tap[1].
| Section | Responsibility | What you do |
|---|---|---|
| Main to outside stop valve (communication pipe) | Water company | Tell the customer how to ask the company about it |
| Outside stop valve to the house (supply pipe) | Property owner, jointly where the pipe is shared | Survey, quote and replace |
| Internal pipework to the kitchen tap | Property owner | Survey, quote and replace |
Shared supplies are common in terraces and converted flats. Before quoting, find out whether the pipe feeds neighbouring properties, because replacing one owner's share can leave a lead section in the shared run.
Identifying lead on a visit
Find the internal stop tap
Lead is often visible where the supply enters the house, usually under the kitchen sink or below the floor near the front wall.
Look at the pipe
Lead pipe is dull grey, has no clear seam, and often has swollen, rounded joints where sections were wiped together.
Scratch test gently
Scrape the surface with a coin or knife. Lead shows a soft, bright silver mark; galvanised steel does not, and copper shows its colour.
Tap test
Lead gives a dull thud when tapped; copper and steel ring.
Check the rest of the run
Look in the boundary stop valve chamber if accessible, and in older houses check for lead branches to outside taps and cisterns.
Record what you saw
Photograph the pipe with the scratch mark and note its location. Do not state lead is present beyond what you have actually seen.
Explaining the risk without causing panic
The facts are serious enough on their own. Lead can build up in the body, so exposure should be kept as low as possible; infants, including unborn babies, and children are at particular risk, and lead can harm mental development in children[1]. In adults it may affect kidney, heart and circulatory health[1]. The legal standard at consumers' taps is 10 micrograms of lead per litre[2].
- Say what you saw: I have found what looks like a lead section here, under your sink.
- Say what it means: lead pipes can add lead to drinking water, and it is best to keep that as low as possible, especially with young children or during pregnancy.
- Say what they can do today: run the kitchen tap before drinking or cooking first thing, to clear water that has stood in the pipe overnight.
- Say what you recommend: ask the water company to test the water at the kitchen tap, and plan to replace the lead section.
- Give it in writing: a short note with photos, so they can share it with family or a landlord.
The flushing advice comes from the DWI, which says a washing-up bowl's worth of water is usually enough, though longer service pipes may need more[1]. It is a stopgap, not a fix.
What the water company can do
Customers are often surprised by how much help is available. A customer can ask their water company to test the water at the kitchen tap, and if the company finds lead pipes or another lead source it should give written advice[1]. Where lead risk exists, companies treat the water with orthophosphate to reduce the problem significantly[1]. The DWI also says companies are legally required to replace their communication pipe if it is made of lead[1].
Some companies run lead replacement schemes or offer to replace their part of the pipe at the same time as the owner's. Terms vary by company, so ask the customer to contact theirs before you dig, and time your work to match theirs where you can. Replacing only the customer's side and leaving a lead communication pipe in place helps less than customers expect.
Planning a compliant supply pipe replacement
- Confirm ownership and whether the supply is shared with neighbours.
- Contact the water company about its communication pipe and any scheme it runs.
- Choose the route: open trench, moling or another trenchless method, depending on ground and surfaces.
- Check the planned depth. A water system laid outside a building less than 750 mm or more than 1,350 mm below ground must be notified to the water company first[4].
- Use approved pipe and fittings, insulate where the pipe enters the building, and fit a new internal stop tap that is easy to reach.
- Flush the new supply well. The DWI advises flushing a tap for at least 10 minutes after any work on a lead pipe[1].
- Issue a certificate if you are an approved contractor, and suggest a follow-up water test.
Lead in solder and old fittings
Pipes are not the only source. Lead-based solder is sometimes used illegally to join copper drinking water pipes, although it is still permitted in closed central heating systems[1]. Older brass fittings can also release lead[1]. If you find bright, heavy solder joints on cold drinking water pipework in a recent extension, or a box of solder on site that is not lead-free, raise it.
Example: a young family in a Victorian terrace
Example: a couple expecting their first baby call about a dripping stop tap in a Victorian terrace in Leeds. Under the sink the plumber finds a dull grey pipe with a wiped joint. The scratch test shows bright silver. The plumber replaces the stop tap, shows the couple the pipe, and gives them a written note with photos, the flushing advice and the water company's contact for a free test.
The test comes back above the standard. The water company confirms its communication pipe is also lead and agrees to replace it the same week as the plumber replaces the supply pipe by moling under the front garden. The new pipe sits within the depth range that avoids notification. After flushing, a second test is well within the limit, and the couple receive a one-page summary they can keep with the house deeds.
Landlords and lead
Landlords own a disproportionate share of older homes, and private rented homes are also the most likely to fail the Decent Homes Standard: 22% did, against 10% of social rented homes[5]. Offering a lead check as part of an annual gas visit is useful to landlords and builds trust. The check takes minutes, because you are already at the kitchen sink and the stop tap. Record the pipe material in the same report as the gas check, and when you find lead, quote replacement as a separate line with photographs. Landlords can then plan the work between contract-holders or tenants rather than in a rush after a complaint, and the record shows they were told. In Scotland the rules for private lets go further; see our guide to Scotland's landlord safety rules.
Keep the language exact on reports: appears to be lead, scratch test bright, recommend water test and replacement. It is accurate, it protects you, and it is easy for a landlord to act on.
Frequently asked questions
Who pays to replace a lead supply pipe?
The owner is responsible for the supply pipe from the outside stop valve into the home and the internal pipework. The water company is responsible for the communication pipe from the main to the stop valve, and some companies run lead replacement schemes.
Is a little lead pipe under the sink a problem?
It can be. Lead can dissolve into water that stands in the pipe, and exposure should be kept as low as possible, especially for babies, children and during pregnancy. A water test and replacement are the safest course.
Does replacing a supply pipe need water company notification?
It does if the new pipe is laid outside a building less than 750 mm or more than 1,350 mm below ground. Other work may need notice too, so check the regulation 5 list.
Can lead solder still be used?
Not on drinking water pipework. Lead-based solder is still permitted in closed central heating systems, which is why mix-ups happen.
References
Drinking Water Inspectorate (2026). Lead in drinking water (opens in a new tab) ↑
legislation.gov.uk (The National Archives) (2016). The Water Supply (Water Quality) Regulations 2016, Schedule 1 (opens in a new tab) ↑
Ministry of Housing, Communities and Local Government (GOV.UK) (2025). English Housing Survey 2023 to 2024: Chapter 1, profile of households and dwellings (opens in a new tab) ↑
legislation.gov.uk (The National Archives) (1999). The Water Supply (Water Fittings) Regulations 1999, regulation 5 (opens in a new tab) ↑
Ministry of Housing, Communities and Local Government (GOV.UK) (2024). English Housing Survey 2024 to 2025: Chapter 1, housing quality (opens in a new tab) ↑