Customer experience

Giving customers honest energy-saving heating advice

Energy-saving heating advice engineers can stand behind: controls, flow temperatures, safe hot water and how to talk about savings without overpromising.

Ava research teamPublished 7 min read

On this page
  1. Why careful advice builds trust
  2. Start with the price of a unit of heat
  3. Advice you can safely give
  4. Never trade safety for savings
  5. Controls: start where the customer is
  6. Heat pump customers need different advice
  7. Winter is when the advice matters most
  8. How to talk about savings
  9. Example: a service visit with useful advice
  10. Frequently asked questions
  11. References

Key takeaways

  • Customers trust engineers' advice on bills more than adverts; keep it specific to their system and modest about savings.
  • Explain the basics of the unit price: at the October to December 2026 cap, electricity cost about 3.3 times as much per kWh as gas.
  • Safe, useful advice centres on controls, timing, flow temperatures, system pressure and servicing.
  • Never trade safety for savings: stored hot water should be kept at 60°C or more to control legionella.

Why careful advice builds trust

Almost every customer asks a heating engineer some version of the same question: how can I make my bills smaller? It is a chance to be genuinely useful, and also a trap. Engineers who repeat headline savings figures, promise that a new boiler will halve a bill or suggest turning everything down regardless of the household can end up with disappointed customers and, occasionally, unsafe systems.

What you say can also become part of the deal. Information a trader gives about a service is treated as a term of the contract where the consumer takes it into account when deciding to go ahead[1]. If a customer agrees to new controls because you said they would save a set amount, you may be held to it. Honest, specific advice is safer for everyone.

The good news is that the most useful advice is also the easiest to stand behind. Showing a customer how their own controls work, setting the boiler up properly and explaining why, and warning them away from unsafe shortcuts will rarely be wrong, and customers remember the engineer who took the time.

Start with the price of a unit of heat

Customers often do not know how their energy is priced. Under the energy price cap for 1 October to 31 December 2026, the average Direct Debit unit rate was 26.32p per kWh for electricity and 7.97p per kWh for gas, with daily standing charges of 54.83p and 29.68p[2]. Per unit, electricity cost about 3.3 times as much as gas[2].

Energy price cap unit rates, 1 October to 31 December 2026 (Direct Debit average)
Energy price cap unit rates, 1 October to 31 December 2026 (Direct Debit average)Comparison. Electricity: 26.32 pence per kWh; Gas: 7.97 pence per kWh.26.32 pence per kWhElectricityElectricity: 26.32 pence per kWh7.97 pence per kWhGasGas: 7.97 pence per kWhEnergy price cap unit rates, 1 October to 31 December 2026 (Direct Debit average)Comparison. Electricity: 26.32 pence per kWh; Gas: 7.97 pence per kWh.26.32 pence per kWhElectricityElectricity: 26.32 pence per kWh7.97 pence per kWhGasGas: 7.97 pence per kWh

Source: Ofgem, 2026[2]

Show the data
ItemValue
Electricity26.32 pence per kWh
Gas7.97 pence per kWh

That ratio explains a lot of what customers see. Plug-in electric heaters are expensive to run as a main heat source. A heat pump can still compete with gas because it delivers several units of heat for each unit of electricity, but only if it is designed, installed and run properly. Explaining this simply helps customers understand why your advice depends on what they have.

Advice you can safely give

Energy advice that is useful and defensible
TopicWhat to sayWhat not to claim
Timer and programmerSet heating to match when you are home, and use the boost button for one-offsThat switching off all day always saves money in every home
Room thermostatFind the lowest comfortable setting and leave it; turning it up does not heat fasterA fixed national saving figure for each degree
Radiator valvesTurn down valves in rooms you use less, keep doors closedThat rooms can be left unheated without any damp risk
Flow temperature on a combiA lower flow temperature can help a condensing boiler run more efficiently, if the house stays comfortableThat one setting suits every home
System pressure and bleedingKeep pressure in the range shown, bleed radiators that are cold at the topThat bleeding radiators will noticeably cut bills
ServicingAn annual service keeps the boiler safe and working as designedThat a service will reduce bills by a set amount

Condensing combis are now the most common boiler in English homes: 63% of homes had one in 2024[3]. Where a combi is set to a higher flow temperature than the home needs, adjusting it with the customer, checking the house stays comfortable, and writing down what you changed is one of the most useful things an engineer can do on a service visit.

Never trade safety for savings

Some popular money-saving tips are unsafe in some homes. The most important for heating engineers is hot water temperature. HSE guidance on legionella says hot water should be stored at 60°C at least to kill legionella bacteria, and outlets should reach 50°C within one minute[4]. Customers with a hot water cylinder who turn it right down to save money may be creating a health risk. Advise them to keep the cylinder at a safe temperature and to save in other ways, such as timing and insulation.

  • Do not advise blocking air bricks, trickle vents or flues to keep heat in.
  • Do not suggest leaving a vulnerable person's home unheated in cold weather to save money.
  • Do not recommend unsafe portable heaters or using a gas cooker for heat.
  • Do warn that very low indoor temperatures can lead to condensation and damp.
  • Do mention scald risk where a cylinder is stored hot and young children or older people use the taps; temperature control at the outlet solves both problems.

Controls: start where the customer is

Smart controls get plenty of attention, but many customers do not use them. In early 2020, only 18% of adults in Great Britain used internet-connected energy or lighting controls, rising to 26% of those aged 35 to 44[5]. The figure is old, so ask rather than assume: many customers still rely on an old programmer they do not fully understand.

Before suggesting new controls, check whether the customer can use the ones they have. Setting up an existing programmer properly and leaving a one-page guide often helps more than an upgrade. Where an upgrade makes sense, explain what it will change for that household, such as heating rooms on different schedules, rather than quoting national figures.

Heat pump customers need different advice

Advice that suits a gas boiler can be wrong for a heat pump. Customers moving from gas often try to run a heat pump the way they ran their boiler: short bursts of heat morning and evening, thermostat turned up when they feel cold, radiators turned off in unused rooms. Heat pumps usually work best running steadily at low flow temperatures, and these habits can make them less efficient and less comfortable.

  • Explain that steady, longer running is normal and expected, not a sign of a fault.
  • Show the customer the schedule and weather settings, and explain any hot water timing.
  • Suggest they compare bills over a full season, not a single cold week.
  • Give them a number to ring if the house is not comfortable, rather than letting them experiment alone.
  • Avoid comparisons with their old gas bill until the system has been set up and used for a while.

If you do not install or service heat pumps, say so and suggest the customer contacts their installer. Well-meant but generic advice from a gas engineer can undo careful commissioning.

Winter is when the advice matters most

Heating demand is intensely seasonal. UK domestic gas demand was 109,126 GWh in the first quarter of 2026, more than five times the 19,636 GWh used in the third quarter of 2025[6]. Customers notice bills in winter, and that is when they are most receptive to advice and most likely to take shortcuts.

5x

UK domestic gas demand in Q1 2026 compared with Q3 2025[6]

Time your advice to that pattern: a short controls refresher at autumn services, a frost-protection reminder before the first cold snap, and a check that customers know how to repressurise a boiler. Advice given in October saves more call-outs in January.

How to talk about savings

  1. Describe the change, not a number

    'This will let the boiler run cooler and condense more of the time' is honest. 'This will save you a third' usually is not.

  2. Make it specific to the home

    Size, insulation, who is home and when, and the type of system all change the result.

  3. Give a range only if you can stand behind it

    If you quote a range, say what it is based on and that results vary.

  4. Suggest the customer watches their own usage

    Smart meter displays and bills before and after are better evidence than any promise.

  5. Write down what you changed

    Record settings in the job report, so the customer and the next engineer know.

Script: 'I've turned the flow temperature down a bit, which should help the boiler run more efficiently. Keep an eye on whether the house stays warm enough. If it doesn't, ring us and we'll adjust it. I can't promise a set saving, because it depends on how you use the heating, but this is the setting the boiler is designed to work best at.'

Example: a service visit with useful advice

Example: during an annual service in a fictional three-bedroom semi, the engineer finds the combi's flow temperature at its factory maximum and the programmer set to heat all day. With the customer's agreement, he lowers the flow temperature, sets the timer for when the household is home and turns down the radiator valves in the spare room. He explains each change, leaves a written note of the settings and promises nothing beyond 'it should run more efficiently'. In this example the customer rings two weeks later, not to complain, but to ask the engineer to do the same at her mother's house.

The habit worth copying is the written note. Recording the settings you changed, and why, turns a passing tip into a service the customer can see and repeat, and it means the next engineer will not undo the change without knowing it was deliberate.

Frequently asked questions

Does turning down the boiler flow temperature save money?

On a condensing boiler, a lower flow temperature can help it run more efficiently, as long as the home stays comfortable. Results vary by home, so avoid promising a fixed saving.

Is it safe to turn my hot water cylinder down to save energy?

Be careful. HSE guidance says stored hot water should be kept at 60°C or more to control legionella. Save energy through timing and insulation instead.

Are smart thermostats worth it?

They can help households with irregular routines or different needs in different rooms. For others, setting up existing controls properly may help just as much.

References

  1. legislation.gov.uk (The National Archives) (2015). Consumer Rights Act 2015, section 50 (opens in a new tab) ↑

  2. Ofgem (2026). Energy price cap unit rates and standing charges (opens in a new tab) ↑

  3. Ministry of Housing, Communities and Local Government (GOV.UK) (2024). English Housing Survey 2024 to 2025: Chapter 2, energy efficiency (opens in a new tab) ↑

  4. Health and Safety Executive (2026). Legionnaires' disease: hot and cold water systems, things to consider (opens in a new tab) ↑

  5. Office for National Statistics (2020). Internet access - households and individuals, Great Britain: 2020 (opens in a new tab) ↑

  6. Department for Energy Security and Net Zero (2026). Energy Trends: UK gas, ET 4.1 natural gas supply and consumption (quarterly), September 2026 (opens in a new tab) ↑

Book a demo

See Ava handle your calls.

Book a short demo. We’ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo