Regulation compliance

Risk assessments for a small plumbing firm

When a plumbing firm must write risk assessments down, how to run HSE's five steps, what clients mean by RAMS, and a one-page template you can adapt.

Ava research teamPublished 7 min read

On this page
  1. What the law requires of a small firm
  2. When you must write it down
  3. The five steps applied to a plumbing firm
  4. Where injuries actually come from
  5. Generic, site-specific and dynamic
  6. RAMS: what clients mean
  7. A one-page template
  8. Example: an emergency leak at night
  9. Sharing assessments with subcontractors and clients
  10. When to review
  11. Frequently asked questions
  12. References

Key takeaways

  • At minimum you must identify hazards, judge how likely and serious harm could be, and remove or control the risk[1].
  • If you employ five or more people, you must record the significant findings: hazards, who might be harmed and how, and your controls[2].
  • Slips, trips and falls on the same level caused 30% of reported non-fatal injuries to employees in 2024/25[3], so the ordinary hazards deserve the most attention.
  • About 95% of UK plumbing and heating enterprises are micro businesses[4], so keep assessments short, specific and used.

What the law requires of a small firm

Risk assessment sounds like paperwork, but the legal minimum is about thinking. HSE explains that under the Management of Health and Safety at Work Regulations 1999, the minimum you must do is identify what could cause injury or illness in your business, decide how likely it is that someone could be harmed and how seriously, and take action to eliminate the hazard or, if that is not possible, control the risk[1]. HSE adds that for most small, low-risk businesses the steps are straightforward[1].

Plumbing and heating sits somewhere between low-risk office work and high-risk construction. You work in other people's homes, often alone, with gas, electricity, hot water, chemicals, heavy loads and ladders. The hazards are well known, which makes a good assessment quicker to write, not less important.

The trade is mostly small firms. Of 47,910 registered UK plumbing, heating and air-conditioning enterprises in 2026, 45,370, about 95%, had 0 to 9 employees[4], and about 48% of plumbers and heating installers were self-employed[5]. The approach in this guide is built for that reality: short documents that fitters actually read.

When you must write it down

5 or more

Employees: the point at which you must record the significant findings of your risk assessment[2]

HSE's guidance is direct: if you employ five or more people, you must record your significant findings, including the hazards, who might be harmed and how, and what you are doing to control the risks[2]. Below that size, the duty to assess still applies; the duty to write it down does not. In practice, most small firms write it down anyway, because clients, insurers and principal contractors ask to see it.

A written assessment also helps you. It is the quickest way to brief a new starter, a subcontractor or an apprentice, and it is your evidence if something goes wrong and someone asks what you had considered.

The five steps applied to a plumbing firm

HSE sets out five steps: identify hazards, assess the risks, control the risks, record your findings and review the controls[2]. Here is how they look for a typical domestic plumbing and heating business.

  1. Identify hazards

    Walk through a normal week: driving, carrying, working in lofts and under floors, soldering, gas work, electrical isolation, hot water, chemicals, sharp tools, dogs, lone working at night. Ask your fitters what worries them.

  2. Assess the risks

    For each hazard, decide who could be harmed, including customers and their children, and how likely and serious harm would be with your current controls.

  3. Control the risks

    Remove what you can, such as moving soldering out of lofts, then control the rest with equipment, procedures and training.

  4. Record your findings

    Write the significant findings on one page per activity, in plain language, with names against any action still to do.

  5. Review the controls

    Revisit after incidents, near misses, new work types or new staff, and at least once a year.

Where injuries actually come from

It is tempting to focus on dramatic hazards. National injury data says the ordinary ones cause most harm. Among non-fatal injuries to employees reported under RIDDOR in 2024/25, slips, trips and falls on the same level made up 30%, handling, lifting and carrying 17%, being struck by a moving object 10%, acts of violence 10% and falls from height 8%[3]. The Labour Force Survey estimates 680,000 workers sustained a non-fatal injury at work in 2024/25[3].

Non-fatal injuries to employees reported under RIDDOR by kind, 2024/25Other kinds of accident make up the remainder.
Non-fatal injuries to employees reported under RIDDOR by kind, 2024/25Bar chart. Slips, trips or falls on the same level: 30%; Handling, lifting or carrying: 17%; Struck by a moving object: 10%; Acts of violence: 10%; Falls from a height: 8%.Slips, trips or falls on the same levelSlips, trips or falls on the same level: 30%30%Handling, lifting or carryingHandling, lifting or carrying: 17%17%Struck by a moving objectStruck by a moving object: 10%10%Acts of violenceActs of violence: 10%10%Falls from a heightFalls from a height: 8%8%Non-fatal injuries to employees reported under RIDDOR by kind, 2024/25Bar chart. Slips, trips or falls on the same level: 30%; Handling, lifting or carrying: 17%; Struck by a moving object: 10%; Acts of violence: 10%; Falls from a height: 8%.Slips, trips or falls on the same levelSlips, trips or falls on the same level: 30%30%Handling, lifting or carryingHandling, lifting or carrying: 17%17%Struck by a moving objectStruck by a moving object: 10%10%Acts of violenceActs of violence: 10%10%Falls from a heightFalls from a height: 8%8%

Source: Health and Safety Executive, 2025[3]

Show the data
ItemValue
Slips, trips or falls on the same level30%
Handling, lifting or carrying17%
Struck by a moving object10%
Acts of violence10%
Falls from a height8%

For a plumbing firm, that points to trailing hoses and cables on site, wet floors after draining down, carrying cylinders and radiators up stairs, and tools or materials falling from height. These belong at the top of your assessment, not at the bottom.

Generic, site-specific and dynamic

Three levels of risk assessment and how a small plumbing firm can use each.
TypeWhat it coversWhen to use it
GenericYour usual activities: boiler installs, bathroom refits, servicing, drain-downs, emergency call-outsWritten once, reviewed yearly, used as the base for every job
Site-specificThe particular hazards of one site: access, asbestos, other trades, occupants, parkingLarger jobs, commercial premises, anything out of the ordinary
DynamicA quick check on arrival, especially for emergenciesEvery call-out, using a short mental or written checklist

The generic set does most of the work. A site-specific note only needs to add what is different. A dynamic check is the fitter's habit on arrival: where is the stop tap and the gas meter, is the electrics safe near the leak, who else is in the house, is there a dog, is the loft safe to enter.

RAMS: what clients mean

Commercial clients, letting agents and builders often ask for RAMS, meaning a risk assessment plus a method statement. The method statement is simply the safe sequence of work: what you will do, in what order, with what equipment and controls. It is not a separate legal document, but it is a useful one.

  • Scope: the job, location, dates and who will do it.
  • Hazards and controls: taken from your generic assessment, plus anything site-specific.
  • Sequence: isolation, drain-down, removal, installation, testing, commissioning, clean-up.
  • Equipment and PPE: access equipment, lifting aids, gloves, eye protection, dust control.
  • Emergency arrangements: first aid, gas and water isolation, contacts.
  • Sign-off: the fitters' signatures to confirm they have read it.

Keep RAMS short. Two pages that the fitter has read beat twenty pages nobody has.

A one-page template

Example layout for a generic risk assessment page. Adapt the rows to your own work.
HazardWho might be harmed and howControls in placeFurther actionBy whom and when
Lifting cylinders and boilersFitters: back injuryTwo-person lifts over a set weight, sack truck, lifting strapsBuy stair-climbing trolleyOwner, next month
Soldering near timberFitters and occupants: fireHeat mats, fire extinguisher in van, check area after workMove to press-fit where practicalOwner, review in spring
Draining down systemsEveryone: slips on wet floorsDust sheets, hose secured to drain, wet floor warningNoneOngoing
Night call-outs aloneFitter: violence, injury with no helpCheck-in call on arrival and leaving, refuse unsafe sitesAdd lone worker appOffice, this quarter

Example: an emergency leak at night

Example: a sole trader in Sheffield takes a late-evening call about water coming through a kitchen ceiling. On arrival the fitter runs through a dynamic check: water near the light fitting, so isolate the lighting circuit before entering; stop tap location unknown, so find the external stop tap first; elderly occupant alone, so keep them out of the wet kitchen. The fitter texts the partner who acts as their check-in contact.

With the water and power off, the fitter finds a split pushed-fit joint above the ceiling. The repair takes thirty minutes. Before leaving, the fitter notes on the job sheet that the lighting circuit was isolated and must be checked by an electrician before use, and tells the occupant the same thing in plain words. The next morning the fitter adds a line to the generic assessment about isolating electrics near leaks.

Sharing assessments with subcontractors and clients

Small firms often use subcontractors for electrical work, plastering or extra labour on busy weeks. Your assessment should cover how they fit in: what they will do, which of your controls apply to them, and who is in charge on site. Send them the relevant pages before they start and ask for theirs in return. If two trades are working in the same space, agree who isolates what and how you will tell each other.

Clients ask for assessments for different reasons. A builder acting as principal contractor needs to coordinate trades. A letting agent wants to show a landlord that contractors are managed. A housing association may have its own format. Keep a master version and adapt it, rather than writing from scratch each time, and keep a copy of what you sent.

The most common gaps in small-firm assessments are easy to fix once you look for them:

  • Customers, children and pets left out of who might be harmed.
  • Driving and van loading missing, even though they take up much of the day.
  • Controls written as be careful instead of a specific action.
  • No owner or date against further actions, so nothing changes.
  • An assessment copied from the internet that mentions equipment the firm does not own.

When to review

  • After any accident, injury or near miss, however minor.
  • When you take on a new type of work, such as heat pumps or commercial maintenance.
  • When someone new joins, especially an apprentice.
  • When equipment changes, for example moving from soldering to press-fit.
  • Once a year in any case, ideally in a quiet week.

Ask one fitter to read each assessment and point out what is missing or wrong. If they cannot recognise their own job in it, rewrite it.

Frequently asked questions

Does a sole trader need a written risk assessment?

The duty to record significant findings applies when you employ five or more people. Sole traders still have to assess and control risks, and many write it down because clients ask for it.

What are HSE's five steps to risk assessment?

Identify hazards, assess the risks, control the risks, record your findings and review the controls.

Is a method statement a legal requirement?

A method statement is not a separate legal requirement, but clients often ask for one alongside the risk assessment. It sets out the safe sequence of work.

How often should risk assessments be reviewed?

Whenever something changes, such as new work, new staff, new equipment or an incident, and at least once a year as good practice.

References

  1. Health and Safety Executive (2026). Managing risks and risk assessment at work (opens in a new tab) ↑

  2. Health and Safety Executive (2026). Steps needed to manage risk (opens in a new tab) ↑

  3. Health and Safety Executive (2025). Non-fatal injuries at work in Great Britain (opens in a new tab) ↑

  4. Office for National Statistics (Nomis) (2026). UK Business Counts - enterprises by industry and employment size band (SIC 2007 class 43.22), via Nomis (opens in a new tab) ↑

  5. Office for National Statistics (Nomis) (2026). Annual Population Survey - occupation (SOC2020) by employment type, via Nomis (opens in a new tab) ↑

Book a demo

See Ava handle your calls.

Book a short demo. We’ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo