Key takeaways
- COSHH requires a suitable and sufficient assessment before work that could expose people to hazardous substances, and the steps it identifies must be put in place[1].
- A safety data sheet is not a risk assessment; use it to make your own[2].
- Firms with five or more employees must record the significant findings[1].
- About 11,000 lung disease deaths a year in Great Britain are estimated to be linked to past exposure at work[3], so fumes and dust deserve real attention.
COSHH in one paragraph
The Control of Substances Hazardous to Health Regulations 2002 apply whenever work could expose employees to a hazardous substance. Regulation 6 says an employer must not carry out such work unless they have made a suitable and sufficient assessment of the risk and implemented the steps it identifies[1]. For a plumbing firm, hazardous substances include products you buy, such as flux and descaler, and things the work creates or exposes you to, such as solder fumes, dust and sewage.
Most plumbing chemicals are used in small amounts for short periods, so the controls are usually simple. The point of the assessment is to make sure everyone knows what those controls are and uses them, especially apprentices and new starters who may not realise that a familiar tin of flux can cause asthma.
The scale of the trade makes this worth doing properly. Total employment in Great Britain's plumbing, heat and air-conditioning installation industry, including working owners, was 187,000 in 2024[4]. Small exposures repeated across a working life add up.
The substances in a typical van
| Product or exposure | Main hazards to check on the SDS | Typical controls |
|---|---|---|
| Soldering flux and solder fumes | Skin and eye irritation, corrosive fluxes, fumes that can cause occupational asthma | Ventilate, keep face out of the fume, gloves, consider press-fit |
| Solvent cement for plastic waste pipe | Flammable vapour, eye and respiratory irritation | Ventilate, no ignition sources, close lids, gloves |
| System descaler and cleaner | Acid or alkaline burns, splash to eyes | Goggles, chemical-resistant gloves, follow dilution and flushing instructions |
| Central heating inhibitor and leak sealer | Usually lower hazard, but check for irritants | Gloves, avoid skin contact, wash hands |
| Drain cleaner | Severe burns, violent reaction with water or other chemicals | Goggles and face protection, gloves, never mix products |
| Glycol antifreeze in heat pump and solar circuits | Toxic if swallowed, especially ethylene glycol | Gloves, label containers, safe disposal |
| Expanding foam and some sealants | Respiratory and skin sensitisers in some products | Ventilate, gloves, follow the SDS |
| Dust from cutting and chasing | Silica and other dusts harmful to lungs | On-tool extraction or water suppression, suitable masks |
| Sewage and wastewater | Biological agents causing infection | Gloves, cover cuts, wash before eating, no hand-to-mouth |
What the assessment must consider
Regulation 6 lists what a suitable and sufficient assessment must take into account[1]. For each product or exposure, work through these points:
- The hazardous properties of the substance.
- Information on health effects from the supplier, including the safety data sheet.
- The level, type and duration of exposure, and the circumstances of the work, including the amount used.
- Activities such as maintenance where exposure may be higher than usual.
- Any relevant workplace exposure limit.
- The effect of the control measures you already have or plan to take.
- Results of any health surveillance or exposure monitoring.
- Combined risks where several substances are used together.
The assessment must be reviewed regularly, and immediately if there is reason to think it is no longer valid or the work has changed significantly[1]. Where an employer has five or more employees, the significant findings and the steps taken must be recorded as soon as practicable[1]. Most UK plumbing firms are micro businesses: 45,370 of 47,910 registered enterprises had fewer than ten employees in 2026[5], so many sit either side of that recording threshold. Writing it down is good practice whatever your size.
Safety data sheets: use them, do not just file them
Suppliers of chemicals must provide an up-to-date safety data sheet if a substance is dangerous for supply[2]. HSE is clear that a safety data sheet is not a risk assessment, and that you should use the information it contains to help make your own assessment[2]. The sheet tells you what the product can do; your assessment says what you will do about it on your jobs.
Ask your merchant or the manufacturer's website for the sheet for every product you carry, and keep them on a shared drive or phone folder that every fitter can open. When you change brands, get the new sheet before the old stock runs out. Products that look the same can have quite different hazards.
Lung health is the long-term risk
Fumes and dust rarely cause immediate harm, which is why they get ignored. HSE estimates that around 11,000 lung disease deaths each year are linked to past exposures at work[3]. Chronic obstructive pulmonary disease accounts for an estimated 35% of those deaths, non-asbestos lung cancer 23%, asbestos-related lung cancer 20% and mesothelioma 20%[3]. HSE also estimates 1.9 million workers were suffering from work-related ill health in 2024/25[3].
- COPD 35%
- Non-asbestos lung cancer 23%
- Asbestos-related lung cancer 20%
- Mesothelioma 20%
- Other disease 3%
Source: Health and Safety Executive, 2025[3]
Show the data
| Item | Value |
|---|---|
| COPD | 35% |
| Non-asbestos lung cancer | 23% |
| Asbestos-related lung cancer | 20% |
| Mesothelioma | 20% |
| Other disease | 3% |
For plumbers, the relevant exposures are solder and flux fumes, dust from cutting, chasing and drilling, and solvent vapours in small rooms. Asbestos is covered by its own regulations, but the same habits apply: control the exposure at source, ventilate, and wear the right mask when you cannot avoid it.
A practical COSHH routine
List what you carry
Empty one van and list every chemical product, plus the exposures the work creates, such as dust and fumes.
Get the data sheets
Collect a current safety data sheet for each product and store them where everyone can reach them.
Remove or substitute
Ask whether a safer product or method would do: press-fit instead of soldering, a milder descaler, ready-mixed inhibitor.
Write one page per product group
Hazards, when exposure happens, controls, PPE, first aid and disposal. Keep it short and specific.
Brief the team
Walk new starters through the sheets and controls, and keep a record that they were briefed.
Review
Check the assessments when products change, after any reaction or incident, and at least yearly.
Dust, sewage and other exposures you create
COSHH is not only about what comes out of a tin. Cutting through masonry to run pipes, chasing walls and drilling concrete produce dust, some of which contains silica. Use tools with dust extraction or water suppression, clean up with a suitable vacuum rather than a brush, and wear a mask suited to the dust when controls are not enough.
Drain and soil work exposes you to biological agents. Cover cuts with waterproof dressings, wear gloves, keep food and drink away from the work, and wash thoroughly before eating or smoking. Legionella bacteria in poorly maintained water systems are also treated as a hazardous substance under COSHH, which is why temperature control and flushing matter on service visits.
Choosing protective equipment that works
Personal protective equipment is the last line of control, not the first, but on plumbing jobs it is often essential. The safety data sheet usually names the type of glove material, eye protection and respiratory protection needed. Buy to that specification rather than grabbing whatever is in the merchant's bargain bin, because the wrong glove can let a chemical through while giving a false sense of security.
- Gloves: match the material to the chemical, replace them when damaged or contaminated, and take them off without touching the outside.
- Eye protection: use goggles, not just safety glasses, for acids, alkalis and anything that could splash.
- Masks: choose a filter suited to the hazard, such as particulate filters for dust and the right cartridge for vapours, and make sure it fits.
- Skin care: wash before breaks, use barrier and after-work creams, and check hands for dryness or cracking.
- Storage: keep PPE clean and dry in the van, away from the chemicals it protects against.
Tight-fitting masks only protect if they seal against the face. If your team uses them regularly, arrange fit testing and remind people that stubble breaks the seal. For short dusty tasks where a mask is uncomfortable, fit on-tool extraction instead; it protects the customer's home as well as your lungs.
Example: a power flush and descale
Example: an engineer in Derby is booked to power flush a sludged system before fitting a new boiler. The firm's COSHH page for system cleaners says the chosen cleaner is mildly acidic, can cause eye damage and must not be mixed with other chemicals. Controls listed are goggles, chemical-resistant gloves, ventilation of the boiler cupboard and disposal of flushed water to the foul drain as the manufacturer instructs.
On site the engineer notices the customer has left a bottle of bleach-based cleaner by the kitchen sink where the waste hose will run. The engineer moves it before starting. After flushing, inhibitor goes in, the hose is rinsed and the empty containers go back in the van. Nothing remarkable happened, which is exactly what a COSHH assessment is for.
Records worth keeping
- A list of hazardous products carried, with the date of each safety data sheet.
- One-page assessments for each product group and for dust and sewage exposures.
- A record of who has been briefed and when.
- Notes of any reactions, near misses or complaints, and what changed afterwards.
If a fitter develops a cough, wheeze or skin rash that improves on holiday, take it seriously. Ask them to see a doctor, review the products they use, and check whether a substitute would remove the cause.
Frequently asked questions
Do sole traders need COSHH assessments?
COSHH places the duty on employers, and the recording duty applies at five or more employees. Self-employed plumbers face the same hazards, and assessing them is the sensible way to protect yourself and your customers.
Is a safety data sheet the same as a COSHH assessment?
No. HSE says a safety data sheet is not a risk assessment. You use its information to make your own assessment of how the product is used on your jobs.
Is solder flux hazardous?
Many fluxes are irritants or corrosive, and fumes from some fluxes can cause occupational asthma. Check the safety data sheet for the product you use and control the fumes.
How often should COSHH assessments be reviewed?
Regularly, and immediately if they may no longer be valid, such as when products, methods or staff change, or after an incident.
References
legislation.gov.uk (The National Archives) (2002). The Control of Substances Hazardous to Health Regulations 2002, regulation 6 (opens in a new tab) ↑
Health and Safety Executive (2026). Chemical safety data sheets (opens in a new tab) ↑
Health and Safety Executive (2025). Work-related ill health and occupational disease in Great Britain (opens in a new tab) ↑
Office for National Statistics (Nomis) (2024). Business Register and Employment Survey: open access (SIC 2007 class 43.22), via Nomis (opens in a new tab) ↑
Office for National Statistics (Nomis) (2026). UK Business Counts - enterprises by industry and employment size band (SIC 2007 class 43.22), via Nomis (opens in a new tab) ↑