Key takeaways
- Training is growing fast: just under 10,000 people completed a recognised heat pump qualification in 2024, 15% more than in 2023[1].
- A course is the start, not the finish; design skills such as room-by-room heat loss and on-site experience are what make installs work[2].
- Nearly half of plumbers and heating installers are self-employed[3], so plan training around lost earning days as well as course fees.
- Working under an umbrella scheme or alongside a certified installer is the most practical way to gain supervised experience[4].
Why the route matters more than the course
Ask a training centre how to become a heat pump installer and you will usually be sold a course. The course matters, but it is the middle of the route, not the whole of it. What makes a heat pump installation work for the customer is the survey, the design, the emitters, the hot water and the set-up, and those are skills you build over several installs, not in a week in a classroom.
The demand for trained people is there. Just under 10,000 people completed a recognised heat pump training qualification in 2024, up 15% on 2023[1], and government says the clean heat and energy efficiency transition could support up to 180,000 additional jobs by 2030[5]. Finding skilled people is already hard: 45% of construction SME employers said recruitment and skills were an obstacle in 2025[6]. An engineer who can survey, design and commission heat pumps properly will not be short of work.
Who pays, and what it really costs
About 71,200 of the UK's plumbers and heating and ventilating installers were self-employed in July 2025 to June 2026, around 48%, against about 77,400 employees[3][7]. For the self-employed, the real cost of training is the course fee plus every day not earning, plus the early installs that take longer than they should. For employers, it is the fee, the engineer's time and the supervision while they learn.
Source: Office for National Statistics (Nomis), 2026[3]
Show the data
| Item | Value |
|---|---|
| Self-employed | 71,200 people |
| Employees | 77,400 people |
Budget for the whole route before you start, so a slow first quarter does not stop you halfway. A route spread over six to twelve months, alongside normal work, is easier to sustain than a block of courses followed by no installs to practise on.
Stage 1: build on what you already know
A good plumber or gas engineer already has most of the wet-system skills a heat pump needs: pipework, pumps, filling and venting, controls wiring at a basic level, and unvented hot water. Make sure those foundations are current before adding anything new, because a heat pump install exposes weak wet-system work quickly.
- Unvented hot water competence, because most heat pump systems store hot water in an unvented cylinder.
- System cleaning, inhibiting and balancing to a standard, not by feel.
- Basic controls and wiring knowledge, and an electrician you can work with for supplies.
- Water regulations and building regulations notification for heating and hot water work.
- Confidence explaining technical choices to customers in plain words.
Stage 2: the heat pump qualification
Choose a recognised heat pump qualification from an accredited centre. MCS links to approved courses for installers, including those planning to work under an umbrella scheme[4]. Check the entry requirements before booking, because many courses expect an existing plumbing or heating qualification and evidence of experience.
A good course should cover how heat pumps work, system design, heat loss calculation, emitter and hot water sizing, controls, commissioning and customer handover. Heat loss is central: MCS certified installers use a BS EN 12831-1 compliant, room-by-room heat load calculation, as required by the MCS heat pump design standard, MIS 3005-D[2]. Ask the centre how much of the course is hands-on with real equipment, and whether it includes a full design exercise from survey notes.
Stage 3: refrigerant work, if you need it
Most domestic air-to-water heat pumps are monobloc units with the refrigerant circuit sealed at the factory, so a plumbing-trained installer connects water pipework rather than refrigerant lines. If you plan to install split systems or air-to-air units, or to open refrigerant circuits for repairs, you will also need the appropriate F-gas certification for that work. Decide early which products you will install, because it changes the training you need and the van stock you carry.
Stage 4: supervised experience
This is the stage most engineers underestimate. Working as a subcontractor to an MCS certified business lets you assess demand, gain experience and work towards certification for your own business[4]. Umbrella scheme operators typically complete the design and commissioning and subcontract all or part of the installation[4], so you see the full process while someone else carries the design responsibility.
Under the redeveloped MCS scheme, a certified business must name a Technical Supervisor, who is responsible for making sure each installation complies with the MCS installation standards[8]. If you want to hold that role in your own business later, keep a log of every install you work on: the design, your role, the commissioning results and what you would do differently.
A route plan you can follow
| Stage | What you do | Evidence to keep |
|---|---|---|
| Foundations | Refresh unvented, system cleaning and controls skills | Current cards and certificates |
| Qualification | Complete a recognised heat pump course | Certificate and design exercise |
| Refrigerant (if needed) | F-gas certification for the work you will do | Certificate and category |
| Supervised installs | Work on installs with a certified business | Install log with designs and results |
| Own designs | Produce designs checked by an experienced designer | Checked heat loss and design sheets |
| Certification decision | Join an umbrella scheme or apply for MCS | Business plan and quality documents |
If you are training employees
Employers face a different risk: you pay for the training and the supervised installs, and a newly skilled engineer is attractive to competitors. Plan the route as a programme rather than a one-off course, and agree it with the engineer in writing.
- Choose one or two engineers who want to specialise, rather than sending everyone on a course.
- Pair each with an experienced designer or installer for their first installs, inside or outside the firm.
- Agree a training agreement covering what you pay for and what happens if they leave soon after, and take advice so it is fair and lawful.
- Give them protected time for surveys and designs, not just installs squeezed between breakdowns.
- Review their designs and commissioning results together after each job for the first few months.
Example: a self-employed engineer's year
Example (fictional): a self-employed gas engineer with a full servicing round wants to add heat pumps. In the first quarter she refreshes her unvented card and books a recognised heat pump course for a quieter month. In the second quarter she agrees with a local certified installer to work on their installs two days a fortnight, keeping her servicing round on the other days.
By the end of the year she has worked on eight installs and produced four designs, which the installer's designer checked and corrected. She joins an umbrella scheme for her first jobs under her own name, using its design review and certification, and keeps her install log ready for the day she applies for MCS herself.
Mistakes to avoid
The most expensive mistake is finishing a course and taking on a full install alone before you have seen several done properly. The second is learning installation but not design, and relying on a manufacturer's quick sizing tool for every quote. The third is underestimating customer conversations: heat pump customers ask about running costs, noise, planning and grants, and your answers need to be accurate and consistent. Treat each of those as part of the training route, and you will spend far less time on callbacks and complaints in your first year.
Choosing a training centre
Check recognition
Confirm the qualification is recognised and the centre is accredited to deliver it.
Check entry requirements
Make sure your existing qualifications and experience meet them before you pay.
Ask about practical time
Find out how many hours are hands-on with working equipment.
Ask about design
Check the course includes a full heat loss and design exercise, not only theory.
Ask about support after
Some centres offer design reviews or links to installers for supervised experience.
Keep learning after certification. Standards, products and tools change: MCS replaced its old heat load spreadsheet with an online calculator and removed the Excel tool from its standards library from 1 April 2026[2]. Budget a few days a year for updates, and read the scheme's changes as they are announced.
Frequently asked questions
How long does it take to become a heat pump installer?
The course itself is short, but getting the design skills and supervised experience to install confidently usually takes several months alongside other work.
Do I need F-gas certification for heat pumps?
Not for connecting the water side of a sealed monobloc unit. You do for work that involves opening refrigerant circuits, such as split systems.
Can I get experience without being MCS certified?
Yes. Working as a subcontractor for an MCS certified business or an umbrella scheme operator is a common route.
What design tool do MCS installers use for heat loss?
MCS provides an online Heat Load Calculator for certified installers and those gaining certification, compliant with BS EN 12831-1.
References
Heating and Hotwater Industry Council (HHIC) (2024). Bumper year for UK heat pumps (opens in a new tab) ↑
MCS (Microgeneration Certification Scheme) (2026). The MCS Heat Load Calculator (opens in a new tab) ↑
Office for National Statistics (Nomis) (2026). Annual Population Survey - regional - occupation (SOC2020) by sex by employment type, via Nomis (opens in a new tab) ↑
MCS (Microgeneration Certification Scheme) (2026). What is an umbrella scheme? (opens in a new tab) ↑
Department for Energy Security and Net Zero (GOV.UK) (2026). Warm Homes Plan (opens in a new tab) ↑
Department for Business and Trade (GOV.UK) (2025). Longitudinal Small Business Survey 2025: SME employers (businesses with 1 to 249 employees) (opens in a new tab) ↑
Office for National Statistics (Nomis) (2026). Annual Population Survey - regional - occupation (SOC2020) by sex by employment type, via Nomis (opens in a new tab) ↑
MCS (Microgeneration Certification Scheme) (2026). Moving over to the redeveloped installer Scheme (opens in a new tab) ↑