Heat pumps low carbon

Heat pump planning rules in Scotland and Wales

How permitted development for air source heat pumps differs in Scotland and Wales from England: unit numbers, size, siting and the 2026 Welsh changes.

Ava research teamPublished 6 min read

On this page
  1. Why devolved rules catch installers out
  2. Wales: the 2026 changes
  3. Scotland: Class 6H
  4. The three nations side by side
  5. Grants differ as well
  6. A routine for cross-border jobs
  7. Mistakes English firms make across the border
  8. Example: two jobs across two borders
  9. Living with older units and earlier rules
  10. When to apply or ask
  11. Frequently asked questions
  12. References

Key takeaways

  • Wales updated its permitted development right on 1 June 2026, allowing two units on detached houses and up to 1.5m³ on houses[1].
  • Scotland's Class 6H allows only one air source heat pump per building and has its own siting tests, including a 1m protrusion limit on dwellings[2].
  • In Scotland the unit must be used only for domestic heating or hot water[2], while England and Wales exclude units used solely for cooling[1][3].
  • Grants differ too: the Boiler Upgrade Scheme covers England and Wales, while Scotland has its own loans and grants[4].

Why devolved rules catch installers out

Planning is devolved, so the permitted development right that lets most air source heat pumps go in without an application is different in England, Wales and Scotland. Installers who learned the English rules can make expensive mistakes when they cross a border, and firms based near Chester, Hereford, Berwick or Carlisle do that every week. The number of local firms shows how much work sits outside England: Scotland had 3,260 plumbing and heating business sites in 2026 and Wales 1,900, against 42,130 in England[5].

Plumbing, heat and air-conditioning business sites by nation, 2026
Plumbing, heat and air-conditioning business sites by nation, 2026Bar chart. England: 42,130 local units; Scotland: 3,260 local units; Wales: 1,900 local units; Northern Ireland: 1,205 local units.EnglandEngland: 42,130 local units42,130 local unitsScotlandScotland: 3,260 local units3,260 local unitsWalesWales: 1,900 local units1,900 local unitsNorthern IrelandNorthern Ireland: 1,205 local units1,205 local unitsPlumbing, heat and air-conditioning business sites by nation, 2026Bar chart. England: 42,130 local units; Scotland: 3,260 local units; Wales: 1,900 local units; Northern Ireland: 1,205 local units.EnglandEngland: 42,130 local units42,130 local unitsScotlandScotland: 3,260 local units3,260 local unitsWalesWales: 1,900 local units1,900 local unitsNorthern IrelandNorthern Ireland: 1,205 local units1,205 local units

Source: Office for National Statistics (Nomis), 2026[5]

Show the data
ItemValue
England42,130 local units
Scotland3,260 local units
Wales1,900 local units
Northern Ireland1,205 local units

This guide compares the rules as published on legislation.gov.uk in November 2026. Planning legislation is amended regularly, and the revised versions online can lag behind recent changes, so check the current text and, where in doubt, ask the local planning authority before you commit to a position.

Wales: the 2026 changes

Wales amended its permitted development right for air source heat pumps, Class G of Part 40, with effect from 1 June 2026[1]. The Welsh rules now allow one heat pump on a house that is not detached or on a block of flats, and two on a detached house[1]. The outdoor unit, including housing, may be up to 1.5m³ on a house and up to 1m³ on a block of flats[1]. As in England, units may not go on a pitched roof, within 1m of the edge of a flat roof, on a scheduled monument or on a listed building or within its curtilage[1].

In conservation areas, the unit may not go on a wall or roof fronting a highway, or nearer to a bounding highway than the house; elsewhere, it may not go on a wall fronting a highway above ground floor level[1]. The unit must comply with the MCS Planning Standards, and it must not be used solely for cooling[1].

Scotland: Class 6H

Scotland's right is Class 6H of Part 1A of its permitted development order, and it works differently. It allows the installation, alteration or replacement of an air source heat pump on a dwelling or within its curtilage, but not if it would result in more than one air source heat pump on the same building or within its curtilage[2]. On a dwelling, no part may protrude more than 1m from the outer surface of an external wall, roof plane, roof ridge or chimney[2].

Within a conservation area, a unit on the dwelling is only permitted at ground floor level on the rear elevation[2]. A unit within the curtilage may not be forward of a wall forming the principal or side elevation where that elevation fronts a road, and no resulting structure may exceed 3m in height[2]. The right does not apply within a World Heritage Site or the curtilage of a listed building[2]. The unit must be used only for domestic heating or hot water, removed when no longer needed, and comply with the MCS Planning Standards for air source heat pumps or equivalent standards[2].

The three nations side by side

Permitted development for domestic air source heat pumps compared[2][1][3]
RuleEnglandWales (from 1 June 2026)Scotland
Units allowed1, or 2 on a detached house1, or 2 on a detached house1 per building or curtilage
Size limit1.5m³ house, 0.6m³ flats1.5m³ house, 1m³ flatsNo volume limit; 1m protrusion limit on a dwelling
CoolingNot if used solely for coolingNot if used solely for coolingOnly for domestic heating or hot water
Conservation areasNot on walls or roofs fronting a highwayNot on walls or roofs fronting a highwayGround floor, rear elevation only, on the dwelling
Listed buildingsExcludedExcludedExcluded within the curtilage of a listed building
NoiseMCS Planning StandardsMCS Planning StandardsMCS Planning Standards or equivalent

Grants differ as well

The Boiler Upgrade Scheme is open in England and Wales. Scotland has separate loans and grants, and Northern Ireland's Boiler Replacement Scheme is closed[4]. A firm working on both sides of the Scottish border needs to know two funding systems, and to make sure its quotes reflect the one that applies at the property address, not the firm's office address.

Building control differs too. Scotland runs its own building standards system, separate from the building regulations that apply in England and Wales, so the paperwork for a heat pump and cylinder installation follows a different route. Check what your scheme memberships cover in each nation before you take the work.

A routine for cross-border jobs

  1. Confirm the nation

    Check which nation the property is in from its postcode and the council, not from the customer's description.

  2. Open the right order

    Use the permitted development order for that nation and check the latest amendments.

  3. Check designations

    Look up listed building status, conservation areas and World Heritage Sites with the local authority.

  4. Apply the siting tests

    Work through number, size or protrusion, roofs, elevations and heights for that nation.

  5. Run the noise check

    Complete the MCS calculation or equivalent standard the order requires.

  6. Check the funding

    Confirm which grant or loan scheme applies at the address before quoting.

  7. Record it

    Keep the checklist, calculation and photos with the job, noting which order you applied.

Mistakes English firms make across the border

  • Fitting a second unit on a detached house in Scotland, where Class 6H allows only one per building.
  • Assuming an air-to-air unit that also cools is covered in Scotland, where the unit must be used only for domestic heating or hot water.
  • Placing a unit on the side wall of a house in a Scottish conservation area, where only the rear ground floor is permitted on the dwelling.
  • Using England's 0.6m³ limit for a block of flats in Wales, where the Welsh limit is 1m³, or the reverse.
  • Quoting the Boiler Upgrade Scheme for a Scottish address.
  • Relying on rules learned before the 2024 Scottish or 2026 Welsh amendments.

Each of these is easy to avoid with a nation-specific checklist, and each can turn a profitable install into a removal, a planning application after the fact or a customer who has lost a grant they expected.

Example: two jobs across two borders

Example (fictional): a heating firm based on the Cheshire side of the Welsh border surveys a detached house in Flintshire. Under the Welsh rules from 1 June 2026 it can fit two units on the detached house, and it places both on the rear elevation after the noise calculation. The quote uses the Boiler Upgrade Scheme, which applies in Wales.

The same month, a firm near Carlisle surveys a semi in Dumfries and Galloway that is in a conservation area. Under Class 6H only one unit is allowed, and on the dwelling it must be at ground floor level on the rear elevation. The firm places a single unit at the rear, checks it protrudes less than 1m from the wall, and directs the customer to Scotland's own funding schemes rather than quoting a grant that does not apply.

Living with older units and earlier rules

You will also meet heat pumps installed under earlier versions of these rules, especially when replacing a unit or adding a second one. A replacement is covered by the same classes, so check the new unit and position against the current rules rather than assuming the old one sets a precedent. If an existing unit looks as if it never met the rules, for example in front of a principal elevation, record it and tell the customer before you replace it in the same spot. Customers selling a house may be asked about it, and a clear note from you saves them a difficult conversation later.

When to apply or ask

If a position fails any test, the installation needs a planning application in that nation, and a listed building will usually need listed building consent as well. Where the rules are unclear, such as an unusual curtilage or a recent amendment, ask the local planning authority or advise the customer to seek a formal decision before work starts. It adds weeks, but it is far cheaper than moving a unit after enforcement action.

For the English rules in detail, see heat pump noise and permitted development rules. Firms working across borders should keep a one-page summary of each nation's rules in the van and update it whenever an amendment order is made.

Frequently asked questions

Can I fit two heat pumps under permitted development in Wales?

Since 1 June 2026, yes on a detached house. Other houses and blocks of flats are limited to one.

Is there a size limit for heat pumps in Scotland?

Class 6H has no volume limit like England's, but a unit on a dwelling must not protrude more than 1m from the wall, roof plane, ridge or chimney, and only one unit is allowed per building.

Can I install a heat pump in a conservation area in Scotland without planning?

On the dwelling, only at ground floor level on the rear elevation, and subject to the other conditions. Otherwise apply for planning permission.

Does the Boiler Upgrade Scheme apply in Scotland?

No. It covers England and Wales. Scotland has its own loans and grants.

References

  1. legislation.gov.uk (The National Archives) (2026). The Town and Country Planning (General Permitted Development) Order 1995, Schedule 2, Part 40 (as it applies in Wales) (opens in a new tab) ↑

  2. legislation.gov.uk (The National Archives) (2024). The Town and Country Planning (General Permitted Development) (Scotland) Order 1992, Schedule 1, Part 1A (opens in a new tab) ↑

  3. legislation.gov.uk (The National Archives) (2025). The Town and Country Planning (General Permitted Development) (England) Order 2015, Schedule 2, Part 14 (opens in a new tab) ↑

  4. GOV.UK (2026). Apply for the Boiler Upgrade Scheme (opens in a new tab) ↑

  5. Office for National Statistics (Nomis) (2026). UK Business Counts - local units by industry and employment size band (SIC 2007 class 43.22), via Nomis (opens in a new tab) ↑

Book a demo

See Ava handle your calls.

Book a short demo. We’ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo