Key takeaways
- Inspections monitor that registered businesses do gas work competently and safely; new and returning businesses can expect probationary checks.
- Inspectors look at three things: the installation, the records and whether the engineer was competent for that category of work.
- After any work on an appliance, the law requires checks of the flue, combustion air, operating pressure or heat input, and safe functioning; your records should show them.
- IGEM/UP/1B Edition 4 became effective on 1 October 2026, so tightness testing and purging procedures and forms should already be updated.
- Treat any finding as a fix-and-learn exercise: put it right, record what you did and brief the whole team.
What an inspection is for
An inspection of your gas work is how the system checks that registration means something. HSE describes the Gas Safe Register as having a team of inspectors who monitor that gas work is being undertaken competently and safely, carrying out risk-based proactive inspections, and notes that new or returning businesses may face a probationary period in which their gas work is inspected[1].
For a well-run business an inspection is routine. It becomes stressful when records are incomplete, procedures have not kept up with changing standards or an engineer has done work outside their categories. All three are within your control, and all three are easier to fix months before a visit than the week before.
The three things inspectors look at
- The installation: whether the appliance, flue, ventilation, pipework and controls on a job you did are safe and to the relevant standards and manufacturer's instructions.
- The records: whether your paperwork for the job shows the tests and checks that were done, the results and any defects found and how they were dealt with.
- Competence: whether the engineer who did the work held the right categories at the time.
The rest of this article takes each in turn. Because the register's inspection findings are not published in a form we can cite, treat what follows as a self-audit built from the legal requirements and standards, not as a league table of common faults.
The installation: the checks the law requires
Regulation 26(9) of the Gas Safety (Installation and Use) Regulations sets the floor. Where a person performs work on a gas appliance, they must immediately afterwards examine the effectiveness of any flue, the supply of combustion air, its operating pressure or heat input (or, where that is not reasonably practicable, its combustion performance) and its operation so as to ensure its safe functioning, and must notify any defect to the responsible person[2].
Most of the appliances you work on are condensing boilers. In 2024, 63% of homes in England had a condensing combination boiler and 19% another type of condensing boiler[3], so the quality of your boiler installs, flue terminations and condensate runs is what an inspector is most likely to see.
Source: Ministry of Housing, Communities and Local Government (GOV.UK), 2024[3]
Show the data
| Item | Value |
|---|---|
| Condensing combination boiler | 63% |
| Other condensing boiler | 19% |
Tightness testing: are you on Edition 4?
IGEM/UP/1B Edition 4, covering tightness testing and direct purging of small natural gas, LPG and LPG/Air installations, was published in March 2026 and became effective from 1 October 2026; Edition 3 was withdrawn on 30 September 2026[4]. If your engineers' test procedures, gauges, job sheets or software templates still follow Edition 3, that is an obvious gap for any work done since October.
For what changed and how to update your paperwork, see the IGEM/UP/1B Edition 4 update.
The records: what a complete job file shows
Inspectors can only see what was done on the day through what you wrote down. A complete job file for gas work usually includes the job sheet, the test results, any commissioning record, any warning notice issued, and photos. For landlord checks, the record has legally required contents, including the date, the address, the landlord's name and address, a description and location of each appliance or flue, any safety defect and remedial action, and the name, signature and registration number of the person who did the check[5].
Commissioning records have moved too. The paper Benchmark commissioning checklist and service record is no longer maintained; the record has moved online and to the Benchmark apps[6]. Make sure every engineer completes the digital version and that you can retrieve it by job.
Unsafe situations: the paperwork that protects you
When you find a dangerous appliance, the law requires you to take all reasonably practicable steps to notify the defect to the responsible person and, where different, the owner of the premises[2]. How you classify the situation, what you do to make it safe and what notice you leave are set by the industry unsafe situations procedure your registration expects you to follow. An inspector will want to see that you followed it and wrote it down.
- Record the classification, the reason for it and the action taken: isolated, capped, labelled or left with the customer's refusal noted.
- Give the customer a warning notice in writing and keep a copy or a photo of it with the job.
- Explain the danger in plain words and record that you did, with the time.
- If the customer refuses to allow you to make the appliance safe, record that refusal and follow the procedure's reporting route.
- Photograph the defect and any label you attach.
This is also where calm, consistent wording matters most. Give every engineer the same short explanation to use, so customers hear the same message whoever attends, and so the record matches what was said. The same discipline applies on the phone: see gas smell call handling procedure for what callers should be told before an engineer arrives.
Self-audit checklist
| Area | What good looks like | Weak point to look for |
|---|---|---|
| Flues | Correct terminal position, supported, sealed, inspection access where needed | Concealed flues without access; terminal too close to openings |
| Combustion and ventilation | Air supply as the manufacturer requires; combustion checked and recorded | Readings not recorded, or analyser out of calibration |
| Operating pressure or heat input | Measured and recorded at commissioning and service | Left blank or 'OK' with no figure |
| Tightness test and purge | Edition 4 procedure, gauge appropriate, results recorded | Old forms; installation volume not calculated before purging |
| Unsafe situations | Classified, customer informed, warning notice issued and recorded | Verbal advice only, no paperwork |
| Records | Complete, legible, signed, retrievable by job | Missing landlord or agent details; unsigned records |
| Competence | Work matched to the engineer's categories on the day | Category expired before the job date |
Preparing for a visit
Review a sample of recent jobs
Pick five jobs per engineer from the last three months and read the records as if you were the inspector. Fix your templates where gaps repeat.
Check categories against jobs
Compare each engineer's categories and expiry dates with the jobs they did. Book reassessments well before expiry.
Calibrate and log equipment
Flue gas analysers, manometers and gauges should be in date for calibration, with certificates on file.
Update procedures
Make sure tightness testing and purging follow Edition 4 and that job sheets capture the new installation volume and purge volume information.
Brief the team
Talk through the self-audit findings at a team meeting and record it.
Contact the customer
If an inspection of a specific job is arranged, confirm the appointment with the customer, explain why and make sure someone can give access.
On the day
Be on time and bring the job file, the engineer's ID card and certificates, and the test equipment used. Let the engineer who did the work attend if possible. Answer questions plainly, show your records and do not argue with observations on site; note them and ask for clarification if needed. Be courteous to the customer, who is giving up their time for a check that ultimately protects them.
After the visit: dealing with findings
- Put right anything unsafe immediately and record what you did, when and who did it.
- For lesser findings, agree the timescale and meet it.
- Ask what the root cause was: a missing step in a template, a training gap, rushing, or an out-of-date procedure.
- Change the process, not just the job: update forms, add the check to your software, brief every engineer.
- Keep a findings log, so you can show at the next inspection that lessons were acted on.
Example: a fictional four-engineer firm's probationary inspection notes that operating pressure readings were written as 'OK' on two job sheets and that one tightness test form was the Edition 3 version. The firm changes its digital job sheet so pressure and heat input fields require a number, removes old forms from the vans and software, and runs a 20-minute briefing on Edition 4. At the next inspection the inspector reviews the findings log and moves on.
Making inspections routine
The firms that find inspections easy treat every job as if it might be inspected. They use the same templates for every job, capture readings as numbers, photograph flues and pipework before boxing in, and review a sample of their own work every month. None of this is extra work in the long run; it is the same work done in a way that can be shown.
For staying on top of qualifications across a team, see planning ACS reassessments. For the registration itself, see registering a business with Gas Safe. For landlord paperwork, see landlord gas safety records.
Frequently asked questions
How often does Gas Safe inspect a registered business?
Inspections are risk-based, and new or returning businesses may have their gas work inspected during a probationary period. There is no fixed schedule that a business can plan around, so keep every job ready to be seen.
What happens if an inspector finds a problem?
Anything unsafe must be put right straight away. Other findings come with a timescale. Record what you did and change your process so it does not happen again.
Do I need to tell the customer about an inspection?
If a specific job of yours is being inspected at a customer's home, contact them to arrange access and explain that it is a routine check on your work.
Does the tightness testing edition matter for inspections?
Yes. IGEM/UP/1B Edition 4 has been effective since 1 October 2026, so work since then should follow it and your forms should reflect it.
References
Health and Safety Executive (2026). Gas Safe Register (opens in a new tab) ↑
Health and Safety Executive (2018). Safety in the installation and use of gas systems and appliances (L56, fifth edition), regulation 26(9) (opens in a new tab) ↑
Ministry of Housing, Communities and Local Government (GOV.UK) (2024). English Housing Survey 2024 to 2025: Chapter 2, energy efficiency (opens in a new tab) ↑
Institution of Gas Engineers and Managers (IGEM) (2026). IGEM/UP/1B Edition 4: Tightness testing and direct purging of small LPG/Air, NG and LPG installations (opens in a new tab) ↑
legislation.gov.uk (The National Archives) (1998). The Gas Safety (Installation and Use) Regulations 1998, regulation 36 (opens in a new tab) ↑
Heating and Hotwater Industry Council (HHIC) (2026). Benchmark goes digital - what homeowners need to know (opens in a new tab) ↑