Key takeaways
- The legal test is Regulation 4: fittings must be of appropriate quality and conform to a British Standard, an equivalent specification or a regulator-approved specification[1].
- WRAS approval is the traditional way to show this, but other Regulation 4 certification schemes exist[2].
- It is not illegal to make or sell non-compliant products, so the duty to check falls on installers and owners[2].
- England's public supply met water quality standards in 99.97% of tests in 2024[3]; the fittings you choose decide whether it stays that clean at the tap.
Approval is evidence, not the law itself
Plumbers often talk about WRAS approval as if it were the legal requirement. It is not. The law, in regulation 4 of the Water Supply (Water Fittings) Regulations 1999, says each water fitting must be of an appropriate quality and standard and suitable for the circumstances in which it is used[1]. A fitting meets that test if it conforms to an appropriate British Standard or another national specification giving an equivalent level of protection and performance, or to a specification approved by the regulator[1].
An approval scheme is how a manufacturer proves that conformity to everyone else. BEAMA, the trade body for the commercial brassware industry, puts it plainly in its compliance guide: WRAS is one way of demonstrating compliance, but the minimum legal requirement is for products to comply with Regulation 4[2]. The distinction matters when a customer hands you a product with no approval mark but a long list of claims.
The approval routes you will meet
| Route | What it is | How to check it |
|---|---|---|
| WRAS approval | The traditional route, now administered by WRAS Approvals; products tested and listed as complying with the regulations when correctly installed | Search the online approvals directory by product or approval number |
| Other Regulation 4 certification | Schemes run by test houses such as NSF and Kiwa that certify compliance with Regulation 4 | Check the scheme's online listing and the certificate's scope and dates |
| British Standard conformity | A fitting that conforms to an appropriate British Standard or equivalent national specification | Documentation from the manufacturer naming the standard, ideally third-party tested |
| Regulator's specification | Conformity with a specification approved by the regulator | Manufacturer documentation and test evidence |
BEAMA notes there are at least two schemes besides WRAS that let manufacturers demonstrate Regulation 4 compliance, run by the test houses NSF and Kiwa, and that both issue certificates and online listings[2]. For specifiers it recommends writing WRAS or equivalent approval into tender documents[2], which keeps the door open to other compliant products without letting uncertified ones in.
Why non-compliant products end up in vans
The uncomfortable fact is that it is not illegal to manufacture and sell non-compliant products[2]. The duty sits with the people who install and own the system. BEAMA says responsibility for compliance falls on users, owners or occupiers and anyone installing plumbing equipment, water fittings and appliances, and that fitting non-compliant products is an offence that could result in prosecution[2].
Online marketplaces and cheap imports make that gap wider. A mixer tap that looks identical to an approved model may use different rubber seals, a different brass alloy or no check valves at all. Typical warning signs include:
- An approval logo with no approval number, or a number that does not appear in any directory.
- Packaging that refers to a different product name or manufacturer than the box contents.
- Hoses and flexible connectors with no markings at all.
- Prices far below the same product from a recognised merchant.
- Claims such as meets UK standards with no standard named.
The supply arrives clean; the fittings decide the rest
Public water in England is heavily tested before it reaches the boundary. The Drinking Water Inspectorate reported overall compliance with standards of 99.97% in 2024[3], with microbiological compliance at 99.98% and chemical compliance at 99.95%[3].
Source: Drinking Water Inspectorate, 2025[3]
Show the data
| Item | Value |
|---|---|
| Microbiological | 99.98% |
| Indicator | 99.97% |
| Chemical | 99.95% |
The same report flags legacy issues such as lead pipes and nickel in domestic dwellings as critical problems that need addressing[3]. Both come from what is fitted inside the property, not from the treatment works. Nickel can leach from some plated fittings, and older brass and illegal lead solder are known lead sources. A fitting chosen without checking its approval can undo the water company's work in the last metre of pipe.
Poor-quality fittings also fail mechanically. Weak seals and thin castings weep, and slow leaks behind panels feed damp: 5% of dwellings in England had a damp problem in 2024[4].
Checking an approval in five minutes
Find the number
Look for an approval or certification number on the product, the box or the installation leaflet. A logo alone is not enough.
Search the directory
Look the number up in the scheme's online directory. Confirm the product name, model and manufacturer match what is in your hand.
Check dates and scope
Approvals expire and are renewed. Make sure the listing is current and covers the use you intend, such as hot water or mains pressure.
Read the installation conditions
Many listings carry conditions, such as a required backflow device or a maximum temperature. Fit to those conditions or the approval does not apply. Some items, such as pumps drawing more than 12 litres per minute or treatment units that discharge waste water, also need notice to the water company before fitting[5].
Record it
Note the approval reference on the job sheet or certificate. If an inspector asks later, you can show your check in seconds.
When the customer supplies the product
Customer-supplied taps, showers and toilets are where most problems start. Decide your policy before the call, then apply it the same way every time.
- If the product has a current approval you can verify, fit it as normal and record the reference.
- If it has no verifiable approval but is a reputable brand with documentation naming a standard, explain the risk and ask the customer to confirm in writing that they want it fitted.
- If it has no evidence at all, or is a drinking water fitting from an unknown source, decline to fit it and offer a compliant alternative.
A short script helps: I can only fit products I can show are compliant with the water regulations, because both of us are responsible if it is not. If you would like, I can supply an approved one at a similar standard.
A buying policy for your van stock
Most non-compliant fittings arrive by accident: a fitter picks up a cheap valve on the way to a job, or a supplier substitutes a similar-looking part when the usual one is out of stock. A short written buying policy closes those gaps without slowing anyone down.
- Buy drinking water fittings from merchants who can show approval details for what they sell.
- Keep a list of approved products you use regularly, with their approval references, and reorder from it.
- Check substitutions before accepting them, especially for valves, flexible connectors and taps.
- Do not carry unmarked flexible hoses or connectors on the van at all.
- Review the list once a year and remove anything whose approval has lapsed.
Example: a marketplace shower mixer
Example: a homeowner in Leicester buys a thermostatic bar shower online and books a plumber to fit it. The box shows an approval-style logo but no number. The plumber searches the brand and model in two directories and finds nothing. The installation leaflet mentions no check valves, and the customer's system is a combination boiler at mains pressure.
The plumber explains the issue, shows the customer the empty search results on a phone, and offers an approved bar shower from the merchant down the road. The customer agrees, returns the original, and the job is done the same afternoon. The plumber writes the new product's approval reference on the invoice. If the customer had insisted on the original, the firm's written policy would have been to decline.
If a non-compliant fitting is already installed
You will often find fittings someone else installed with no evidence of approval. You do not have to replace them on sight, but you should not ignore them either. Explain what you found, why it matters and what you recommend, and put it in writing on your job sheet or report.
Where a fitting could contaminate the supply, such as an unprotected connection to a heating circuit or a hose fitting with no check valve, recommend replacement on the same visit and do not add to the problem by connecting new work to it. Where the risk is lower, such as an unmarked but sound basin tap, record it and quote for replacement. Either way, the customer can decide with full information, and your notes show you raised it.
Frequently asked questions
Is it illegal to fit a product that is not WRAS approved?
Not if the product meets Regulation 4 another way, such as through another recognised certification scheme or conformity with an appropriate British Standard. It is an offence to fit a product that does not comply.
Are WRAS and Water Regs UK the same thing?
WRAS was the Water Regulations Advisory Scheme. Product approvals are now administered by WRAS Approvals, while the water industry's regulations guidance body operates as Water Regs UK.
Is a manufacturer's PDF certificate enough proof?
Treat it as a starting point. Confirm the approval number in the scheme's online directory, because certificates can be out of date or for a different model.
Do central heating components need water regulations approval?
Components that only carry closed-circuit heating water are not drinking water fittings, but anything connected to the supply, such as a filling loop, cold feed or mixing valve, is.
References
legislation.gov.uk (The National Archives) (1999). The Water Supply (Water Fittings) Regulations 1999, regulation 4 (opens in a new tab) ↑
BEAMA (2022). Adhering to the UK Water Regulations (opens in a new tab) ↑
Drinking Water Inspectorate (2025). Drinking Water 2024: summary of the Chief Inspector's report for drinking water in England, foreword (opens in a new tab) ↑
Ministry of Housing, Communities and Local Government (GOV.UK) (2024). English Housing Survey 2024 to 2025: Chapter 1, housing quality (opens in a new tab) ↑
legislation.gov.uk (The National Archives) (1999). The Water Supply (Water Fittings) Regulations 1999, regulation 5 (opens in a new tab) ↑