Technology AI

Thermal imaging cameras for plumbers: worth buying?

What a thermal camera can and cannot find for heating engineers, from underfloor heating leaks to cold radiators, and how to write a fair report.

Ava research teamPublished 6 min read

On this page
  1. What a thermal camera actually measures
  2. Where it earns its keep
  3. Where it misleads
  4. Tracing an underfloor heating leak
  5. Good habits on site
  6. What to look for when buying
  7. Writing a fair customer report
  8. Leaks, water bills and customers' questions
  9. Is it worth buying? A worked example
  10. Frequently asked questions
  11. References

Key takeaways

  • A thermal camera shows surface temperature differences, not water; it works best on heating pipes and hot water.
  • Its strongest uses are underfloor heating leaks, pipe routes, radiator problems and heat loss checks.
  • Shiny surfaces, cold water and small temperature differences produce misleading images.
  • Reports should describe what the image shows and what was confirmed, never guess at causes.
  • It pays for itself only if you will offer leak tracing or heating diagnostics often enough.

What a thermal camera actually measures

A thermal imaging camera measures infrared radiation from surfaces and turns it into a colour map of apparent temperature. It does not see water, pipes or damp directly. It sees that one part of a floor, wall or radiator is warmer or cooler than the area around it. For a heating engineer that is very useful, because hot water in a pipe or a leak from a heating circuit warms the surface above it.

Hidden leaks and damp are common problems. 5% of dwellings in England, about 1.4 million homes, had a damp problem in 2024, up from 4% in 2021 and 2022[1]. Not all of that is plumbing, but customers with a damp patch often ring a plumber first, and a thermal camera helps you decide quickly whether a heating or hot water pipe is the likely source.

Where it earns its keep

  • Underfloor heating: tracing pipe layouts, finding a leak in a screed floor and checking whether every loop is warming.
  • Radiators: showing cold spots at the bottom from sludge, cold tops from trapped air, and uneven heating across a system before and after balancing or a power flush.
  • Pipe routes: finding where heating and hot water pipes run in walls and floors before drilling or lifting boards.
  • Hot water leaks under floors and in ducts, where the warm plume shows through the surface.
  • Cylinder, manifold and pump checks, to see whether valves and zones are opening as expected.
  • Heat loss: showing customers missing insulation, cold bridging or draughts as part of a heating upgrade survey.

Each of these works because there is a clear temperature difference. Run the heating or hot water first, so the circuit you are looking at is noticeably warmer than the room.

It also saves damage. Lifting one board or cutting one small square of screed in the right place is far cheaper, for you and the customer, than opening a whole floor on a hunch. Customers notice that, and they mention it when they recommend you.

Where it misleads

  • Shiny surfaces such as copper, chrome, stainless steel and glazed tiles reflect heat from elsewhere, so the reading is wrong. A strip of matt tape on the surface gives a truer reading.
  • Cold water leaks are hard to see, because the leak may be the same temperature as the floor around it.
  • Small temperature differences, in warm rooms or with low flow temperatures, make faint images that are easy to over-read.
  • A cool patch on a wall can be damp, a cold bridge, missing insulation or a draught. The image alone does not tell you which.
  • Sunlight on a wall or floor and recent furniture movement create false hot and cold areas.

Treat the image as a pointer, not proof. Confirm with a pressure test, a moisture meter, an acoustic leak detector or a small inspection opening before you tell the customer where the leak is.

Tracing an underfloor heating leak

  1. Confirm a leak exists

    Isolate the UFH circuits and pressure test each loop to find which one is losing pressure.

  2. Cool the floor

    Let the floor settle to room temperature, with rugs and furniture moved where you can.

  3. Heat the suspect loop

    Run warm water through the losing loop only, and watch the floor as the pattern appears.

  4. Look for the bloom

    A leak usually shows as a warm area spreading outside the regular line of the pipe.

  5. Confirm before cutting

    Use a second method, such as acoustic detection, and mark the smallest possible opening.

  6. Record everything

    Save thermal and normal photos of each stage, with time and loop number, for the report.

Good habits on site

Thermal imaging is a skill. Two engineers with the same camera can reach opposite conclusions in the same room, so agree a routine and train everyone who uses it.

  • Record room temperature, outside conditions and how long the circuit has been running before each image.
  • Take a wide image first to show context, then close-ups of anything interesting.
  • Fix the colour scale manually when comparing images, or the camera rescales each shot and differences look larger or smaller than they are.
  • Photograph the same area with the normal camera from the same position.
  • Note anything that could confuse the image: radiators nearby, sunlight, recent cooking, pets lying on the floor.
  • Keep a library of good and bad examples from your own jobs to train new engineers.

Ask the customer about the history before you start. A damp patch that appears only after heavy rain points away from the heating system; one that grows when the heating runs points towards it. That conversation often saves more time than the camera.

What to look for when buying

Thermal camera features and why they matter
FeatureWhy it matters for plumbing and heating
Detector resolutionHigher resolution shows pipe runs and small leaks from further away
Thermal sensitivityBetter sensitivity picks up faint differences in low-temperature systems
Visual and thermal blendOverlaying a normal photo makes images understandable to customers
Phone attachment or standaloneAttachments are cheaper and share easily; standalone units are tougher and quicker to use
Report softwareSaves time producing customer reports with images, notes and spot readings
Emissivity adjustmentLets you correct readings for different surfaces
Durability and batteryIt will be dropped in lofts and used in the cold

A phone attachment is a sensible way to learn whether you will use thermal imaging. If you find yourself using it most weeks, a standalone camera with better sensitivity and report software is the upgrade.

Writing a fair customer report

A thermal image is persuasive, which is why it must be described carefully. The law expects any service to be performed with reasonable care and skill[2], and a report that overstates what an image proves can lead a customer to pay for the wrong work. Disputes about home repair are costly: house and garden maintenance and repair had a median net consumer detriment of £109 per problem in a government study, among the highest of any sector[3].

  • Say what was done: which circuits were heated, for how long, and the conditions in the room.
  • Show the thermal image next to a normal photo of the same area.
  • Describe the pattern, for example a warm area spreading from the pipe line near the kitchen door.
  • Say what confirmed it, such as a pressure drop on loop three and acoustic detection at the same point.
  • Separate findings from recommendations, and give options with their limits.
  • Avoid words like proves or definitely unless a second method confirmed the result.

Leaks, water bills and customers' questions

Customers increasingly ask about leaks because they hear about water loss. In England, leakage accounted for 19% of water put into public supply in 2024 to 2025, against 59% for household consumption[4]. Most of that leakage is in water company networks, not homes, but a customer with a high metered bill may suspect a leak on their side.

Where water put into public supply in England went, 2024 to 2025
Where water put into public supply in England went, 2024 to 2025Donut chart. Household consumption: 59%; Leakage: 19%; Non-household consumption: 19%; Unbilled and operational use: 3%.Household consumption: 59%Leakage: 19%Non-household consumption: 19%Unbilled and operational use: 3%Leakage 19%
  • Household consumption 59%
  • Leakage 19%
  • Non-household consumption 19%
  • Unbilled and operational use 3%

Source: Environment Agency (GOV.UK), 2025[4]

Show the data
ItemValue
Household consumption59%
Leakage19%
Non-household consumption19%
Unbilled and operational use3%

Thermal cameras are rarely the right tool for a buried cold water supply pipe in the garden. Acoustic detection, tracer gas and meter checks with all taps closed do that job better. Tell the customer which method suits their problem rather than reaching for the camera because you own one.

Is it worth buying? A worked example

Example: a fictional heating firm fits and repairs underfloor heating and is asked to trace two or three UFH leaks a month, which it currently passes to a specialist. It buys a standalone camera and an acoustic detector, trains two engineers and adds a priced leak-tracing visit to its list. In the first year it also uses the camera on power flushes to show customers before-and-after radiator images, which helps explain the work. The owner reviews use after twelve months by counting tracing jobs, flush jobs where images were used and any cases where the camera pointed the wrong way.

Use the same test yourself. If you would use the camera less than once a fortnight, a phone attachment, or a specialist subcontractor for leak tracing, is likely to be better value.

Frequently asked questions

Can a thermal camera find water leaks?

It finds temperature differences. Leaks from heating and hot water pipes usually show well; cold water leaks often do not. Confirm with a second method before opening floors or walls.

Is a phone thermal camera good enough?

For learning and occasional use, often yes. For regular leak tracing and customer reports, a standalone camera with better sensitivity and report software is quicker and more reliable.

Why does copper pipe look cold on the camera?

Shiny metal reflects heat from its surroundings, so its reading is wrong. Put matt tape on the pipe or measure a painted section instead.

Can I charge for thermal imaging?

Many firms price leak tracing or heating diagnostics as a separate visit. Explain in advance what the survey includes and that a further opening may be needed to confirm.

References

  1. Ministry of Housing, Communities and Local Government (GOV.UK) (2024). English Housing Survey 2024 to 2025: Chapter 1, housing quality (opens in a new tab) ↑

  2. legislation.gov.uk (The National Archives) (2015). Consumer Rights Act 2015, section 49 (opens in a new tab) ↑

  3. Department for Business, Energy and Industrial Strategy (GOV.UK) (2021). Consumer protection study 2022: understanding the impacts and resolution of consumer problems (opens in a new tab) ↑

  4. Environment Agency (GOV.UK) (2025). Water resources 2024 to 2025: analysis of the water industry's annual water resources performance (opens in a new tab) ↑

Book a demo

See Ava handle your calls.

Book a short demo. We’ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo