Boilers heating

Combi vs system boiler: an advice framework for installers

A practical way to advise customers on combi vs system boilers: hot water demand, mains flow, bathrooms, space and the English rules that apply.

Ava research teamPublished 7 min read

On this page
  1. The question behind 'which boiler is better'
  2. How the three systems compare
  3. Five questions that decide it
  4. Measure the mains before you recommend anything
  5. Worked Example: two houses on the same street
  6. Mistakes that turn a sound choice into a call-back
  7. The rules that shape the choice in England
  8. Explaining it so the customer can decide
  9. Frequently asked questions
  10. References

Key takeaways

  • Combis are now the default in English homes, so the real job is spotting the households where a combi will disappoint[1].
  • Decide on simultaneous hot water demand and measured mains flow, not on bedroom count or habit.
  • In England a replacement combi needs one extra efficiency measure on top of time and temperature controls; system and heat-only boilers do not[2].
  • Write the reason for your recommendation on the quote so the customer can see why you chose it.

The question behind 'which boiler is better'

Customers rarely ask about boiler types in the abstract. They ask because a shower runs cold when the kitchen tap opens, because a cylinder takes up a cupboard they want back, or because a neighbour told them combis are cheaper to run. Your advice has to answer the problem they actually have, and it has to survive the first winter of use.

The starting point in England is that combis already dominate. The English Housing Survey found that 63% of homes had a condensing combination boiler in 2024 and 19% had another condensing boiler, against 2% and 1% in 2001[1]. That shift means most customers have lived with a combi and will expect one. The useful skill is recognising the minority of homes where a combi is the wrong tool.

Households in England and Wales by number of bedrooms, 2021Census 2021; bedroom count is a starting point, not the deciding factor
Households in England and Wales by number of bedrooms, 2021Column chart. One bedroom: 11.4%; Two bedrooms: 27.1%; Three bedrooms: 40.4%; Four or more: 21.1%.0%20%40%60%One bedroom: 11.4%11.4%One bedroomTwo bedrooms: 27.1%27.1%Two bedroomsThree bedrooms: 40.4%40.4%Three bedroomsFour or more: 21.1%21.1%Four or moreHouseholds in England and Wales by number of bedrooms, 2021Column chart. One bedroom: 11.4%; Two bedrooms: 27.1%; Three bedrooms: 40.4%; Four or more: 21.1%.0%20%40%60%One bedroom: 11.4%11.4%OnebedroomTwo bedrooms: 27.1%27.1%TwobedroomsThree bedrooms: 40.4%40.4%ThreebedroomsFour or more: 21.1%21.1%Four ormore

Source: Office for National Statistics, 2021[3]

Show the data
ItemValue
One bedroom11.4%
Two bedrooms27.1%
Three bedrooms40.4%
Four or more21.1%

House size is a rough guide at best. Census 2021 put 40.4% of households in England and Wales in three-bedroom homes and 21.1% in homes with four or more bedrooms[3]. A four-bedroom house with one bathroom and two adults may be fine on a combi; a three-bedroom house with a family of five and an en-suite may not.

How the three systems compare

Practical differences to explain at survey stage
FactorCombiSystem boiler with unvented cylinderRegular boiler with vented cylinder
Hot water deliveryOn demand, limited by mains flow and boiler outputStored at mains pressureStored, gravity or pumped pressure
Two outlets at onceFlow splits between themHandles several outlets if mains flow is goodHandles several outlets, pressure often low
Space neededBoiler onlyBoiler plus cylinder cupboardBoiler, cylinder and loft tanks
Depends on mainsFullyFully, but buffered by the storeLittle
After a long bathNo waitRecovery time for the cylinderRecovery time for the cylinder
Extra rules in EnglandOne extra efficiency measure requiredUnvented cylinder competence neededUsually kept for existing open-vented layouts

Keep the regular boiler column in mind even though it is rarely the first choice. Where a home has weak mains flow, a big old cylinder and loft tanks in good order, keeping the open-vented layout can be the honest recommendation.

Five questions that decide it

  1. How many hot water outlets will run at the same time at the busiest moment of the day? Count showers, baths and the kitchen tap, not bathrooms on the plan.
  2. What does the mains actually deliver? Measure dynamic flow and pressure at the kitchen cold tap, then again with a second tap open.
  3. Is there a bath that gets filled often? Filling time on a combi is set by flow rate, and families notice it.
  4. Where will a cylinder go, and does the customer want that cupboard back? Space is a legitimate reason, but say what it costs in hot water performance.
  5. Is there a renewable or heat pump plan? A cylinder now can make a later heat pump or solar diverter easier, so ask about plans for the next ten years.

If the answers point both ways, the simultaneous-use question wins. Customers forgive a smaller boiler cupboard far more readily than a shower that goes cold when someone runs the dishwasher.

Measure the mains before you recommend anything

  1. Record static pressure

    Fit a gauge to an outside tap or the kitchen cold tap with nothing else running and note the reading.

  2. Measure dynamic flow

    Open the kitchen cold tap fully into a flow cup or a measured bucket and time it. Note the pressure while it runs.

  3. Repeat with a second outlet open

    Open a bath or basin tap and measure again. This is the figure that predicts complaints.

  4. Check the supply pipe

    Look at the stopcock and the incoming pipe. Old lead or a narrow supply shared with a neighbour limits any mains-pressure option.

  5. Compare against the product data

    Check the combi's hot water flow rating and the unvented cylinder's minimum flow and pressure in the manufacturer's literature before you commit.

  6. Write the readings on the survey

    If performance is later disputed, dated readings show what the mains delivered on the day.

Worked Example: two houses on the same street

Example. House A is a three-bedroom semi with one bathroom, two adults and a teenager. The kitchen tap measures a healthy flow and the reading barely drops with the bath tap open. The busiest moment is one shower plus the kitchen tap. A correctly chosen combi suits them, frees the airing cupboard and removes loft tanks.

Example. House B is a four-bedroom detached with a family bathroom and two en-suites, two adults and three children who shower before school. The mains is good but the flow halves when a second outlet opens. A combi would leave someone in a lukewarm shower most mornings. A system boiler with an unvented cylinder sized for the morning peak is the better answer, and the extra space it needs is the honest trade.

A quick way to sanity-check combi hot water is the rule of thumb that output in kilowatts is roughly litres per minute multiplied by the temperature rise and by 0.07. In this Example, a winter supply needing a large rise to reach shower temperature shows why the rated flow on the data sheet is only achievable in warmer months, which is worth saying out loud to the customer.

Mistakes that turn a sound choice into a call-back

  • Quoting a combi on the hot water flow figure from the brochure without checking that the mains can feed it. The boiler cannot deliver water the supply pipe does not bring in.
  • Fitting a large combi to cover hot water and leaving it badly oversized for the heating load, so it short-cycles through spring and autumn.
  • Recommending a cylinder without asking where the discharge pipe from the safety valves will run. Tundish and discharge routes often decide the cylinder position.
  • Keeping a tired vented cylinder on a new system boiler because it still holds water, then fielding complaints about slow recovery and scale.
  • Removing loft tanks without checking what else they fed, such as a shower pump, an outside tap or a cold supply to a far bathroom.
  • Forgetting that a mains-pressure system pushes harder on old pipework and fittings. A weeping joint that never showed on gravity can show within days.

Most of these come from a rushed survey rather than a wrong opinion. Build them into your survey sheet as tick boxes so whoever surveys asks the same questions every time, whether it is you or a new engineer on their first month.

When the customer is torn, a two-option quote is fair: price the combi and the cylinder system side by side, list what each one does and does not do for their household, and let them choose with the facts in front of them.

The rules that shape the choice in England

Boiler Plus set a 92% ErP minimum for gas boilers in English homes, made time and temperature controls explicit, and requires a replacement combi to come with one of four extra measures: flue gas heat recovery, weather compensation, load compensation, or smart controls with automation and optimisation[2]. The government left system and heat-only boilers out of the extra-measure rule because retrofitting those devices could create a Legionella risk without additional work[2].

92%

Minimum ErP efficiency for a gas boiler installed in an English home[2]

Approved Document L adds two points that bear on the choice. A combi should be selected to modulate down to the typical heating load of the dwelling, and when a boiler is replaced each room should have thermostatic room controls[4]. Both affect which model you quote, not just which type.

Unvented cylinders bring their own competence requirement and annual maintenance expectations. If you do not hold the unvented qualification, either partner with someone who does or say so plainly rather than steering the customer towards a combi that does not fit their needs.

Explaining it so the customer can decide

Lead with the household, not the product. A short script that works on the doorstep: 'With your mains as it is, a combi will give one good shower at a time. When two people shower at once, one of them will notice. A cylinder fixes that but needs this cupboard. Which matters more to you?'

  • Name the trade-off in one sentence and let the customer choose it.
  • Show the flow readings you took, not a brochure figure.
  • Put the deciding factor on the written quote so it does not get lost.
  • If you recommend against what they asked for, say why and offer to quote both.

Record the customer's choice and the reason on the survey sheet. If they pick a combi against your advice for a busy house, a note signed off at quote stage saves an argument about hot water in January.

For the follow-on decisions, see sizing the boiler from heat loss and the replacement survey checklist.

Frequently asked questions

Is a combi or a system boiler cheaper to run?

Running costs depend more on correct sizing, flow temperature and controls than on boiler type. A combi avoids cylinder standing losses; a well-insulated cylinder can suit homes with heavy, simultaneous hot water use. Explain the trade-off rather than promising a saving.

How many bathrooms is too many for a combi?

There is no fixed number. What matters is how many outlets run at the same time and what the mains delivers with two outlets open. Measure it on the survey.

Do system boilers need the Boiler Plus extra measure?

No. In England the extra measure applies to gas combination boilers. System and heat-only boilers still need time and temperature controls and must meet the 92% ErP minimum.

Can I fit an unvented cylinder without extra training?

Unvented hot water storage is controlled work with its own competence requirement. Check you hold the right qualification or work with someone who does before quoting it.

References

  1. Ministry of Housing, Communities and Local Government (GOV.UK) (2024). English Housing Survey 2024 to 2025: Chapter 2, energy efficiency (opens in a new tab) ↑

  2. Department for Business, Energy and Industrial Strategy (GOV.UK) (2018). Boiler Plus: new standards for domestic boiler installations from April 2018, frequently asked questions (opens in a new tab) ↑

  3. Office for National Statistics (2021). Housing, England and Wales: Census 2021 (opens in a new tab) ↑

  4. Ministry of Housing, Communities and Local Government (GOV.UK) (2023). Approved Document L, Volume 1: Dwellings (2021 edition incorporating 2023 amendments) (opens in a new tab) ↑

Book a demo

See Ava handle your calls.

Book a short demo. We’ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo