Boilers heating

Hard water areas: limescale protection on boiler installs

What counts as hard water under Approved Document L, how to check an address, which scale protection to fit and what to record so warranties hold.

Ava research teamPublished 7 min read

On this page
  1. What the guidance actually asks for
  2. Why combis are where scale does its damage
  3. Check hardness for the address, not the county
  4. Choosing the protection
  5. Worked Example: a combi in a hard water town
  6. Spotting scale on boilers you did not fit
  7. Explaining scale protection without sounding like an upsell
  8. Record what you fitted
  9. Frequently asked questions
  10. References

Key takeaways

  • Approved Document L treats water above 200ppm of calcium carbonate as hard and expects treatment of the feed to water heaters and combi hot water circuits[1].
  • The same expectation carries into the 2026 edition, so it is not going away[2].
  • Combis are in most English homes, which puts scale-sensitive plate heat exchangers on most of your jobs[3].
  • Test or look up hardness for the actual address, choose protection to match the manufacturer's instructions, and record it on the commissioning record.

What the guidance actually asks for

Hard water is one of the few local conditions that the Building Regulations guidance names directly. Approved Document L defines hard water as water with a total hardness greater than 200ppm of calcium carbonate[1]. In its commissioning section it says that in hard water areas suitable measures should be taken to treat the feed water to water heaters and to the hot water circuit of combination boilers to reduce limescale build-up[1].

The 2026 edition, which takes effect on 24 March 2027 for most work in England, keeps the same instruction alongside the expectation that systems are cleaned, dosed with inhibitor and commissioned to BS 7593[2]. Scale protection is therefore part of a compliant installation, not an optional extra to upsell.

The guidance says 'suitable measures'. It does not name a product. What is suitable depends on the hardness, the appliance and what its manufacturer's installation instructions require.

Why combis are where scale does its damage

Limescale forms fastest where hard water is heated, and in a combi that happens inside the plate heat exchanger, through narrow passages that clog quickly. The symptoms customers report are fluctuating hot water temperature, reduced flow, noise when the tap is running and, eventually, overheat faults. Each of those is a call-back that looks like a boiler fault but is really a water quality problem.

The exposure is large because most homes now have a combi. The English Housing Survey found 63% of homes in England had a condensing combination boiler in 2024, with another 19% on other condensing boilers[3].

Homes in England by boiler type, 2024Remainder calculated from the published shares
Homes in England by boiler type, 2024Donut chart. Condensing combination boiler: 63%; Other condensing boiler: 19%; Other boilers or no boiler (remainder): 18%.Condensing combination boiler: 63%Other condensing boiler: 19%Other boilers or no boiler (remainder): 18%63% combi
  • Condensing combination boiler 63%
  • Other condensing boiler 19%
  • Other boilers or no boiler (remainder) 18%

Source: Ministry of Housing, Communities and Local Government (GOV.UK), 2024[3]

Show the data
ItemValue
Condensing combination boiler63%
Other condensing boiler19%
Other boilers or no boiler (remainder)18%

Cylinder systems are not immune. Immersion elements, coils and the hot side of the cylinder scale up too, and an unvented cylinder's valves dislike debris. But the combi plate is usually the first part to suffer and the most visible to the customer.

Check hardness for the address, not the county

Broad maps are a starting point only. Hardness follows the supply zone, which depends on the water source, so two towns in the same county can differ sharply. As a general pattern, much of eastern and south-eastern England is supplied with hard water while large parts of Scotland, Wales, Northern Ireland and the north-west of England are soft, but there are exceptions in every region.

  1. Look up the postcode

    Use the water supplier's own hardness lookup for the property and save a screenshot to the job.

  2. Test on site if in doubt

    A test strip or a drop-count kit on the kitchen cold tap takes two minutes and settles the question.

  3. Convert the units

    Suppliers quote different units. Milligrams per litre of calcium carbonate is the same as ppm; one degree Clark is about 14.3ppm.

  4. Check for a softener

    If a base-exchange softener is fitted, note whether it serves the boiler feed and whether a hard drinking tap is kept.

  5. Record the result

    Write the hardness and its source on the survey so whoever commissions the boiler knows which protection to fit.

Choosing the protection

Common ways to meet the hard water expectation
OptionHow it worksWhere it fitsPoints to check
Polyphosphate dosing unitReleases a small dose that keeps hardness salts in suspensionCombi cold inlet, compactCartridge needs replacing; check the product is approved for drinking water
Electrolytic scale reducerSmall current changes how crystals formCombi cold inletEffectiveness varies with flow; follow approval listings
Electronic or electromagnetic conditionerSignal through coil around the pipeWhere space is tightNeeds power; evidence varies by product
Base-exchange softenerRemoves hardness by ion exchangeWhole house in very hard areasKeep a hard drinking tap; check boiler maker's rules on softened water in heating circuits
Lower hot water temperatureLess heat, slower scalingAll combis, alongside a deviceCustomer must still get hot enough water

Three decision criteria cover most jobs. First, read the boiler's installation instructions, because many state a hardness above which a scale reducer must be fitted and some name the type. Second, match the device to the hardness you measured: a compact inline unit suits moderately hard supplies, while very hard areas with a customer who also suffers scale on taps and showers may justify a whole-house softener. Third, think about upkeep. A dosing cartridge that is never changed protects nothing, so build its replacement into the annual service.

Softeners deserve care. Most manufacturers have rules about filling a sealed heating circuit with softened water, and the inhibitor still needs to go in. If a softener is fitted, many installers fill the heating circuit from a hard supply upstream of it; check what the boiler and inhibitor makers say before you decide.

Worked Example: a combi in a hard water town

Example. A two-bedroom terrace in a chalk-supplied town is getting a new combi. The supplier's lookup gives about 290ppm and a drop test on the kitchen tap agrees. The boiler manual requires a scale reducer above a stated hardness and recommends limiting the hot water temperature. The engineer fits a polyphosphate unit on the cold inlet, sets the hot water temperature to the lowest setting the household is happy with, and records the hardness, the device and its cartridge change interval on the commissioning record.

Example. At the first annual service the engineer swaps the cartridge and checks the hot water flow and temperature against the commissioning figures. If flow has fallen noticeably, that is an early sign the protection is not keeping up and worth investigating before the plate fails.

Spotting scale on boilers you did not fit

Repair calls in hard areas often turn out to be scale. Recognising it early saves a wasted parts order and gives the customer a clear choice between descaling, replacing the plate and fitting protection, or planning a replacement.

  • Hot water temperature surges and drops at a steady tap, while heating works normally.
  • Kettling or banging only when hot water is drawn, not during central heating.
  • Hot water flow lower than the household remembers, with no change in the cold flow at the same tap.
  • Overheat lockouts during hot water use, especially on long showers.
  • White or grey deposits visible on the cold inlet filter or around the plate connections when you open them up.

Before condemning a plate heat exchanger, rule out the simpler causes: a blocked cold inlet filter, a sticking flow sensor or diverter valve, and a hot water temperature set too high. If the plate is badly scaled, replacing it without fitting protection simply restarts the clock, so quote both together and explain why.

For landlords with several properties in the same hard area, a short note on the pattern you are seeing across their stock is genuinely useful. It helps them plan protection at the next boiler replacement rather than paying for repeated hot water repairs.

Keep a simple log of which postcodes produce scale call-backs. After a winter or two it tells you where to be firm about protection at quote stage and which products have held up.

Explaining scale protection without sounding like an upsell

Customers in hard areas already know what scale looks like; they descale their kettles. Use that. 'Your water here leaves scale like the inside of your kettle. Inside the boiler, the hot water part has passages thinner than a pencil lead, and the regulations expect us to protect it. This unit does that. It needs a new cartridge each year, which we do at the service.'

  • Present scale protection as part of the installation, priced in, not a later add-on.
  • Show the hardness reading so the customer can see why it applies to them.
  • Mention the ongoing part, such as cartridge changes, at quote stage rather than at the first service.
  • If they decline a whole-house softener, record that it was offered.

Record what you fitted

The commissioning record is where the hardness, the device and the hot water settings belong. The Benchmark record has moved online and to apps, replacing the paper checklist[4], which makes it easier to attach the hardness lookup and a photo of the installed unit. Warranty assessors look for evidence that water treatment was addressed, and a complete record answers the question quickly.

There is also your own position to consider. A service contract carries an implied term that the work is done with reasonable care and skill[5]. Fitting a combi in a hard area with no protection, against the manufacturer's instructions, is hard to defend when the plate scales up in two years.

For the paperwork that follows, see registering boiler warranties and manufacturer installer schemes.

Frequently asked questions

What hardness counts as hard water for building regulations?

Approved Document L defines hard water as a total hardness greater than 200ppm of calcium carbonate. Above that, it expects suitable measures to treat the feed to water heaters and combi hot water circuits.

Is a scale reducer a legal requirement?

Approved Document L is guidance on meeting the Building Regulations, and it expects suitable treatment in hard water areas. Manufacturers' instructions often require a scale reducer above a stated hardness, and warranties may depend on it.

Can a softener feed a combi?

Usually yes for the hot water side, but check the boiler and inhibitor makers' rules on softened water in the sealed heating circuit and keep a hard drinking water tap.

How do I convert degrees Clark to ppm?

One degree Clark is about 14.3ppm of calcium carbonate. Milligrams per litre of calcium carbonate and ppm are the same.

References

  1. Ministry of Housing, Communities and Local Government (GOV.UK) (2023). Approved Document L, Volume 1: Dwellings (2021 edition incorporating 2023 amendments) (opens in a new tab) ↑

  2. Ministry of Housing, Communities and Local Government (GOV.UK) (2026). Approved Document L, Volume 1: Dwellings (2026 edition) (opens in a new tab) ↑

  3. Ministry of Housing, Communities and Local Government (GOV.UK) (2024). English Housing Survey 2024 to 2025: Chapter 2, energy efficiency (opens in a new tab) ↑

  4. Heating and Hotwater Industry Council (HHIC) (2026). Benchmark goes digital - what homeowners need to know (opens in a new tab) ↑

  5. legislation.gov.uk (The National Archives) (2015). Consumer Rights Act 2015, section 49 (opens in a new tab) ↑

Book a demo

See Ava handle your calls.

Book a short demo. We’ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo