Boilers heating

Boiler replacement survey checklist

A boiler replacement survey checklist: customer needs, flue, gas supply, condensate, mains flow, system condition, controls, access, CO alarms, paperwork.

Ava research teamPublished 6 min read

On this page
  1. Why the survey decides the job
  2. Before you arrive
  3. The customer's needs
  4. The technical checklist
  5. Flue checks that most often change the job
  6. Combi suitability: the mains water test
  7. Carbon monoxide alarms
  8. Regulations and paperwork
  9. Look ahead to low-carbon options
  10. Turn the survey into a quote
  11. Example: a survey that saved an install day
  12. Frequently asked questions
  13. References

Key takeaways

  • A good survey prevents the three most expensive surprises on install day: an unsuitable flue route, an undersized gas supply and a dirty system.
  • Ask about how the household uses hot water before you look at the boiler; it decides whether a combi suits them.
  • Measure mains flow and pressure at the kitchen tap for any combi proposal, and write the result down.
  • Only 62% of homes in England had a carbon monoxide alarm in 2024[1]; check and advise on every survey.
  • The installer has a wide duty to make sure an appliance can be used without danger once installed[2]; the survey is where that starts.

Why the survey decides the job

Most install-day problems were visible at the survey to anyone who looked. A flue that cannot terminate where the old one did, a gas pipe too small for a higher-output combi, a condensate route that will freeze, a system full of sludge: each of these turns a one-day swap into a two-day job, a variation and an awkward conversation. A consistent survey, done the same way every time, is what lets a firm quote accurately and fit without surprises.

It also carries legal weight. Under the Gas Safety (Installation and Use) Regulations, no one may install a gas appliance unless it can be used without constituting a danger to any person, and HSE guidance describes this as a wide-ranging duty covering the appliance, the way it is installed, its fittings, its flue and its surroundings[2]. Work on gas fittings must be done by someone in a class approved by HSE, in practice Gas Safe registered[3].

Before you arrive

  • Ask for photos of the boiler, the flue outside and the gas meter, so you arrive with the right equipment and questions.
  • Ask the boiler make and model and its age if known.
  • Ask how many bathrooms and showers there are and how many people live in the property.
  • Ask whether the customer is considering a move of the boiler, a change of system type or a heat pump.
  • Check whether the property is in a conservation area or is a flat with building management rules, which can affect flue positions.

The customer's needs

Start with the people, not the pipes. Five minutes of questions saves the wrong boiler being fitted.

  1. How many people, and how many baths or showers might run at the same time?
  2. Any plans to extend, add a bathroom or convert the loft?
  3. Problems with the current system: cold radiators, slow hot water, noise, pressure loss?
  4. Preferences on controls: basic, programmable, smart, or app-based?
  5. Budget, timing and whether the current boiler is still working.

Write the answers on the survey sheet. They justify your recommendation later, for example why you are proposing to keep a cylinder rather than converting to a combi.

The technical checklist

Technical survey checklist for a boiler replacement; adapt for system conversions and relocations.
AreaWhat to checkRecord
Existing applianceMake, model, type, output, condition, signs of spillage or overheatingPhotos, model plate
FlueTerminal position, clearances to openings, boundaries, plume direction, route options for the new boilerMeasurements, photos outside
Gas supplyMeter type and position, pipe size and route, length and fittings to the boiler, other appliances on the supplySketch of route, pipe sizes
CondensateInternal termination to a waste, or external route and its protection from freezingProposed route
Mains waterStatic pressure and flow rate at the kitchen tap, incoming pipe size and materialReadings with time of day
System conditionWater condition from a radiator or drain point, sludge, corrosion, pump and valvesPhoto of water sample
Radiators and pipeworkNumber, sizes, valves, any cold spots, microbore or old pipeworkRoom-by-room notes
Hot waterCylinder type and condition if staying, or removal if convertingPhotos
Controls and electricsExisting controls, wiring centre, fused spur, earthingPhotos
AccessLoft ladders and boarding, cupboard sizes, parking, stairsMeasurements

The gas supply deserves extra care, because it is the hidden extra most often missed on combi upgrades. The separate guide on gas pipe sizing on boiler surveys covers it in detail.

Flue checks that most often change the job

The flue is where a like-for-like swap most often stops being like-for-like. Old boilers were frequently fitted with terminals in positions that no longer meet the manufacturer's clearances for a new condensing appliance, and a new boiler's plume behaves differently from the old one's.

  1. Measure the terminal's distance to windows, doors, air bricks, gutters, boundaries and facing walls, and compare with the new model's installation manual.
  2. Look at where the plume will drift: towards a neighbour's window, a path or a parked car. A plume management kit may be needed.
  3. Check whether the flue route passes through a void or ceiling space where it would need to be inspectable.
  4. For loft or cupboard positions, measure the maximum flue length available and check it against the model's limits.
  5. Photograph the outside wall, the terminal and the surroundings from far enough back to show the clearances.

If the flue has to move, price it as part of the job, not as an extra discovered on the day. Customers accept flue work on a quote; they resent it on an invoice.

Combi suitability: the mains water test

A combi heats water on demand from the incoming main, so its hot water performance can never be better than the cold supply feeding it. Measure static pressure and flow rate at the kitchen tap, note the time of day, and compare the result with the manufacturer's stated requirements for the model you are considering. If the flow is poor or the household runs several showers at once, a system boiler with a cylinder may serve them better. Explain this with the reading in hand; customers accept a recommendation far more readily when they have seen the evidence.

Carbon monoxide alarms

Every survey is a chance to check for a working carbon monoxide alarm. In 2024, 62% of dwellings in England had one, up from 60% the year before[1], which still leaves millions without.

Dwellings in England with a carbon monoxide alarm
Dwellings in England with a carbon monoxide alarmComparison. 2023: 60%; 2024: 62%.60%20232023: 60%62%20242024: 62%Dwellings in England with a carbon monoxide alarmComparison. 2023: 60%; 2024: 62%.60%20232023: 60%62%20242024: 62%

Source: Ministry of Housing, Communities and Local Government (GOV.UK), 2024[1]

Show the data
ItemValue
202360%
202462%

All carbon monoxide alarms fitted in the UK must meet EN 50291-1:2018, although the rules on where they are required differ between England, Wales, Scotland and Northern Ireland[4]. The NHS lists gas boilers among household appliances that can produce carbon monoxide when badly installed, faulty or poorly maintained[5]. Note whether an alarm is present, its age and position, and include one in the quote where it is needed or advisable.

Regulations and paperwork

  • Building regulations: replacing a heating system can need approval[6]. Note whether you will notify through your competent person scheme, so the homeowner does not need to arrange approval[7].
  • Condensing boilers: in England, replacement boilers must be condensing; note any reason the property makes this difficult, such as condensate routes[8].
  • Commissioning records: the paper Benchmark checklist is no longer maintained and the record has moved online and to apps[9]; note what details you will need on the day.
  • After any work on the appliance, the operating pressure or heat input, flue, combustion air and safe operation must be checked[2]; plan your commissioning time accordingly.

Look ahead to low-carbon options

Many customers replacing a gas boiler now ask whether a heat pump would suit them, even if they end up choosing another boiler. A few extra notes on the survey let you answer properly and keep the conversation for later: outdoor space for an external unit, radiator sizes room by room, pipe sizes, insulation and glazing, and space for a cylinder if the home currently has a combi. You do not need a full heat loss survey to have that conversation, but you do need enough information to say honestly whether it is worth one.

Turn the survey into a quote

  1. Recommend one option clearly

    Boiler type and output, position and flue, with one sentence on why it suits this household.

  2. List every item the survey found

    Gas supply upgrade, flue extension, condensate route, system clean, filter, controls, CO alarm.

  3. Name the assumptions

    Anything you could not check, such as pipe routes under floors, as a stated assumption or provisional sum.

  4. Attach the evidence

    Photos and readings that support the extras. Customers rarely argue with a photo of sludge in a radiator sample.

  5. Send it fast

    Same day for straightforward swaps, within 48 hours for anything more complex.

Example: a survey that saved an install day

Example (fictional): an engineer surveying a semi in Wolverhampton for a combi upgrade found the gas pipe from the meter ran a long route with several bends, measured a modest mains flow at the kitchen tap with two showers in the house, and drew black water from a bedroom radiator. The quote recommended a system boiler keeping the existing cylinder, a gas pipe upgrade and a chemical clean with a magnetic filter, each with a photo or reading. The customer accepted, the install took the day planned, and there were no variations.

Survey every job as if someone else will fit it. If the installer would have to ring you with a question, the survey is not finished.

Frequently asked questions

What should a boiler replacement survey include?

Customer needs, the existing appliance, flue options, gas supply, condensate route, mains water pressure and flow, system condition, radiators, hot water, controls, access and CO alarms, with photos and readings.

How do I know if a combi suits a property?

Ask about simultaneous hot water use and measure mains pressure and flow at the kitchen tap. Compare the readings with the manufacturer's requirements for the model.

Should I check carbon monoxide alarms on a survey?

Yes. Only 62% of homes in England had one in 2024[1]. Alarms must meet EN 50291-1:2018[4].

Does a boiler replacement need building regulations approval?

Replacing a heating system can[6]. Installers registered with a competent person scheme notify the work, so the homeowner does not need to arrange approval[7].

References

  1. Ministry of Housing, Communities and Local Government (GOV.UK) (2024). English Housing Survey 2024 to 2025: Chapter 1, housing quality (opens in a new tab) ↑

  2. Health and Safety Executive (2018). Safety in the installation and use of gas systems and appliances (L56, fifth edition) (opens in a new tab) ↑

  3. legislation.gov.uk (The National Archives) (1998). The Gas Safety (Installation and Use) Regulations 1998, regulation 3 (opens in a new tab) ↑

  4. Heating and Hotwater Industry Council (HHIC) (2025). A guide to carbon monoxide (CO) alarm legislation for heating engineers (opens in a new tab) ↑

  5. NHS (2026). Carbon monoxide poisoning (opens in a new tab) ↑

  6. GOV.UK (2026). Building regulations approval (opens in a new tab) ↑

  7. GOV.UK (2026). Building regulations approval (opens in a new tab) ↑

  8. Ministry of Housing, Communities and Local Government (GOV.UK) (2024). English Housing Survey 2024 to 2025: Chapter 2, energy efficiency (opens in a new tab) ↑

  9. Heating and Hotwater Industry Council (HHIC) (2026). Benchmark goes digital - what homeowners need to know (opens in a new tab) ↑

Book a demo

See Ava handle your calls.

Book a short demo. We’ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo