Boilers heating

A repeatable fault-finding workflow for boiler repairs

A step-by-step boiler fault-finding workflow that cuts revisits and parts guessing: triage, safety first, fault codes, testing, repair and records.

Ava research teamPublished 6 min read

On this page
  1. Why a workflow, when you already know boilers
  2. Stage 1: triage before you set off
  3. Stage 2: make it safe and confirm the complaint
  4. Stage 3: use the manufacturer's diagnostic route
  5. Stage 4: test, do not guess
  6. The kit that makes testing quick
  7. Stage 5: repair, then re-check everything
  8. Stage 6: record what you found and why
  9. Keeping the customer informed while you work
  10. Worked Example: the lockout that was not the board
  11. Stage 7: learn from repeat faults
  12. Frequently asked questions
  13. References

Key takeaways

  • A fixed sequence beats experience alone: the same steps on every job stop engineers jumping to the part they replaced last week.
  • Safety comes first and last: after any work on a gas appliance, the law requires checks of flue, combustion air, pressure or heat input and safe operation[1].
  • Fault codes point to a circuit, not a part; test before you order.
  • Engineers already work long paid weeks, so every avoidable revisit costs time you cannot get back[2].

Why a workflow, when you already know boilers

Experienced engineers fix most faults quickly because they recognise patterns. The trouble is that patterns mislead on the jobs that matter most: the intermittent fault, the model you see twice a year, the boiler that shows one code for three different causes. That is where parts get fitted on a hunch, the fault returns and the customer starts to doubt you.

A written workflow does not replace experience. It makes sure the basics are done every time, so experience is spent on the hard part. It also makes your firm's work consistent, which matters when a new engineer joins or when you look back at why a job needed three visits.

Time is the scarce resource. Employee plumbers and heating installers had median total paid hours of 40 a week in 2026, against 36.9 for all UK employees[2]. A revisit does not just cost fuel; it takes a slot from another customer.

Median total paid hours per week, 2026ASHE 2026 provisional
Median total paid hours per week, 2026Comparison. Employee plumbers and heating installers: 40 hours; All UK employees: 36.9 hours.40 hoursEmployee plumbers and heating installersEmployee plumbers and heating installers: 40 hours36.9 hoursAll UK employeesAll UK employees: 36.9 hoursMedian total paid hours per week, 2026Comparison. Employee plumbers and heating installers: 40 hours; All UK employees: 36.9 hours.40 hoursEmployee plumbers and heatinginstallersEmployee plumbers and heating installers: 40 hours36.9 hoursAll UK employeesAll UK employees: 36.9 hours

Source: Office for National Statistics, 2026[2]

Show the data
ItemValue
Employee plumbers and heating installers40 hours
All UK employees36.9 hours

Stage 1: triage before you set off

Good fault-finding starts on the phone. The more you know before arriving, the more likely you are to bring the right part and the right test equipment.

  • Make, model and, if possible, a photo of the data badge.
  • The fault code or the pattern of lights, and when it appears.
  • What the customer has lost: heating, hot water or both.
  • System pressure on the gauge and whether it has been topped up recently.
  • Any recent work, power cuts, frozen weather or changes to controls.
  • Whether anyone has a headache, dizziness or other signs that could suggest carbon monoxide.

If the call suggests carbon monoxide, the advice is to stop using the appliance and seek medical advice[3], and the call becomes a safety call, not a repair booking. Many firms use a script for this so whoever answers asks the same questions; an AI employee such as Ava can take these details on first contact and pass them to the engineer before they set off.

Stage 2: make it safe and confirm the complaint

On arrival, look before you touch. Check the area around the boiler and the flue terminal, smell for gas, look for signs of spillage or water damage, and ask the customer to show you the fault. Confirm the symptom yourself. A surprising number of 'boiler faults' turn out to be controls set wrongly, a timer in the wrong mode or a frozen condensate pipe.

  • Check gas supply to the property and other appliances.
  • Check electrical supply, fused spur and any external controls.
  • Check system pressure and, on combis, the incoming cold water flow.
  • Read the fault history if the boiler stores one, not just the current code.

Stage 3: use the manufacturer's diagnostic route

Every manufacturer publishes fault-finding charts for its models. Use them. A fault code tells you which circuit or safety device tripped, not which component failed. An ignition lockout might be gas supply, the electrode, its lead, the condensate backing up into the burner, the flue, or the board.

Follow the chart from the start rather than jumping to the most expensive part. Where the chart tells you to measure a resistance, a voltage or a pressure, measure it and write the figure down.

Stage 4: test, do not guess

Starting points for common boiler symptoms; always follow the model's own fault chart
SymptomFirst checksCommon causes
No ignition or lockoutGas pressure, electrode gap and lead, condensate trap, flueBlocked condensate, worn electrode, gas supply
Low pressure losing over daysVisible leaks, pressure relief valve discharge, expansion vessel chargeFlat vessel, leak, weeping valve
Hot water but no heatingControls demand, diverter valve, pumpDiverter stuck, thermostat wiring, pump
Heating but no hot water on a combiFlow sensor, diverter, cold inlet filterDiverter, flow sensor, blocked filter
Overheat faultPump, circulation, bypass, heat exchanger flowPump, air, sludge, closed valves
Noisy boilerAir, pump speed, heat exchanger scale or sludgeSludge, scale, low pressure

Prove a component faulty before replacing it. Where you cannot test it directly, look for evidence that eliminates the alternatives. If you replace a part and the fault persists, you have learned something, but the customer has paid for your lesson unless you have explained the risk beforehand.

The kit that makes testing quick

Engineers guess at parts when testing is slow or awkward. A well-stocked diagnostic kit, kept in the same place in every van, removes that excuse.

  • Calibrated flue gas analyser, with its calibration certificate in date.
  • Digital manometer for gas and appliance pressures.
  • Multimeter with leads suitable for low-voltage boiler circuits and a set of probe adaptors.
  • Thermometer or thermal camera for flow, return and heat exchanger checks.
  • Expansion vessel pressure gauge and a pump for recharging.
  • Manufacturer fault charts and wiring diagrams on a tablet or phone, downloaded for offline use.
  • Inspection mirror and torch for burners and condensate traps.

Check the kit monthly. A dead multimeter battery or an analyser out of calibration turns a forty-minute diagnosis into a parts guess.

Stage 5: repair, then re-check everything

After the repair, run the boiler through heating and hot water demand and watch for the fault. Then carry out the checks the regulations require after work on a gas appliance: the effectiveness of the flue, the supply of combustion air, the operating pressure or heat input, and safe operation[1]. Any defect must be notified to the responsible person[1].

  1. Confirm the cure

    Reproduce the conditions that caused the fault and check it no longer occurs.

  2. Combustion check

    Run a combustion analysis after any work on the gas or combustion side.

  3. Gas tightness

    Test where gas connections have been disturbed.

  4. Final safety checks

    Flue, combustion air, pressure or heat input and safe operation.

  5. Customer demo

    Show the customer the boiler working and explain what you found.

Stage 6: record what you found and why

The job sheet is the most useful fault-finding tool for the next visit. Record the symptom as reported, the symptom as confirmed, the readings taken, the cause identified, the part replaced and the post-repair checks. If you could not find the fault, say what you ruled out.

Records also protect you. A service contract carries an implied term of reasonable care and skill[4], and where no time was agreed, a reasonable time[5]. A clear diagnostic record shows you approached the fault methodically, even if it took two visits.

Keeping the customer informed while you work

Diagnosis can look like standing around to a customer who wants hot water back. A short explanation of what you are doing and why turns that impression into confidence.

  1. Say what you are checking first and why: 'I am going to check the gas and the condensate before anything else, because they cause this code more often than the parts people usually replace.'
  2. Tell them when you have found the cause, before you start the repair.
  3. If a part is needed, explain how sure you are, what it will cost and when it can be fitted.
  4. If you cannot find the fault today, say what you have ruled out and what happens next.

Honesty about uncertainty builds more trust than false confidence. Customers forgive a second visit they were warned about far more readily than a part that did not work.

Worked Example: the lockout that was not the board

Example. A combi locks out every few days with an ignition fault. A previous engineer replaced the electrode and later the board. The fault returned both times. On triage, the customer mentions it happens on cold mornings.

Example. The engineer confirms the code in the fault history, checks gas pressure and electrode, then follows the chart to the condensate route. The external condensate pipe is long, thin and uninsulated, and partially freezes overnight, backing water up into the boiler. The engineer reroutes it internally, records the cause, and explains why the earlier parts did not fix it.

Stage 7: learn from repeat faults

Once a month, look at jobs that needed more than one visit. Group them by model and fault. Patterns emerge quickly: a model whose diverter fails often, a postcode with scale problems, an engineer who replaces boards too readily. Use what you find to adjust van stock, training and the triage script. See improving first-time fix rates and triage questions for no-heating calls.

Frequently asked questions

Should I replace the part the fault code points to?

Not without testing. A code identifies a circuit or safety device; follow the manufacturer's fault chart and prove the part faulty before replacing it.

What checks are required after a repair?

After working on a gas appliance, examine the flue, combustion air, operating pressure or heat input, and safe operation, and notify any defect.

What if I cannot find an intermittent fault?

Record what you tested and ruled out, check the fault history, ask the customer to note when it happens, and agree the next step rather than guessing at parts.

What should the job sheet include?

The reported and confirmed symptom, readings, cause, parts fitted, post-repair checks and anything ruled out.

References

  1. legislation.gov.uk (The National Archives) (1998). The Gas Safety (Installation and Use) Regulations 1998, regulation 26 (opens in a new tab) ↑

  2. Office for National Statistics (2026). Annual Survey of Hours and Earnings 2026 provisional, Table 14 (occupation by 4-digit SOC 2020) (opens in a new tab) ↑

  3. NHS (2026). Carbon monoxide poisoning (opens in a new tab) ↑

  4. legislation.gov.uk (The National Archives) (2015). Consumer Rights Act 2015, section 49 (opens in a new tab) ↑

  5. legislation.gov.uk (The National Archives) (2015). Consumer Rights Act 2015, section 52 (opens in a new tab) ↑

Book a demo

See Ava handle your calls.

Book a short demo. We’ll walk through your calls and workflow, and agree what Ava should take care of.

Book a demo