Key takeaways
- Measure average job value by work type, not across the whole business; a single average hides more than it shows.
- Agree the price before you start: where no price is agreed, the law only entitles you to a reasonable one[1].
- Offer two or three written options on bigger jobs and let the customer choose; it raises value without pressure.
- Respect cancellation rights on off-premises contracts: 14 days, and no work in that period without an express request[2][3].
- Most of the gain comes from fewer small, unprofitable visits and better-scoped quotes, not from upselling.
What average job value tells you
Average job value is turnover divided by the number of jobs in a period. As a single figure for the whole business it is almost meaningless, because a heating firm does very different kinds of work: a tap washer, an annual service, a boiler replacement and a heat pump installation sit in different worlds. Split it by work type and the number starts to tell you something.
The spread inside the heat pump market alone shows why. Under the Boiler Upgrade Scheme, the median installed cost of an air-to-water heat pump was £12,826 in July to September 2026, against £34,630 for a ground source system[4]. Mixing those jobs with short call-outs in one average produces a number that changes every time the work mix shifts, whether or not anything got better.
Source: Department for Energy Security and Net Zero, 2026[4]
Show the data
| Item | Value |
|---|---|
| Air-to-water heat pump | £12,826 |
| Ground source heat pump | £34,630 |
Track four averages instead: repairs and breakdowns, servicing, replacements, and project work such as bathrooms or heat pumps. Then ask a narrower question for each: are we leaving value on the table, or are we doing work that should not be done at this price at all?
Start with the jobs that pull the average down
The quickest honest gain usually comes from the bottom of the range, not the top. Small jobs that take a full slot, need a parking permit and a merchant visit, and are invoiced at half an hour of labour lower the average and fill the diary at the same time.
- Set a minimum charge that covers travel and the first hour, and say it clearly on the phone and the website.
- Group small jobs by area and day, so a dripping tap waits for a slot near another job rather than getting its own trip.
- Ask on the phone whether there is anything else the customer wants looked at while the engineer is there.
- Decline work that is consistently unprofitable for you and refer it to a handyman or a smaller firm.
- Review jobs that needed a second visit; a return trip halves the value of the job it belongs to.
None of this needs a sales technique. It needs the price of a visit to reflect what a visit costs, and the person answering the phone to collect enough detail to send the right engineer with the right parts.
Options customers actually welcome
On bigger jobs, a written quote with two or three clear options does more for job value than any doorstep conversation. Customers like choosing, and many pick the middle option when they can see what each includes. The important part is that every option is a genuine recommendation you would be happy to fit.
| Option | What it includes | Who it suits |
|---|---|---|
| Essential | Like-for-like combi swap, standard controls, chemical flush and inhibitor, manufacturer warranty registered | Tight budgets, landlords, homes being sold soon |
| Recommended | As Essential, plus a magnetic filter, smart or weather-compensating controls and an extended warranty | Most owner-occupiers planning to stay several years |
| Complete | As Recommended, plus a power flush, replacing problem radiators or valves, and a first-year service booked | Older systems with sludge, poor circulation or cold spots |
Price each option fully, with the labour, materials and any making good spelt out. Put the differences in plain words: what the customer gets, not product codes. If an option only makes sense for some homes, such as a power flush on a new system, leave it out rather than padding the list.
Bundles that make sense
Bundling raises value when it saves the customer a separate visit or a separate decision. It backfires when it feels like a menu of extras. Good bundles in heating work tend to be things a careful engineer would mention anyway.
- Service plus carbon monoxide alarm check and replacement where an alarm is missing or out of date.
- Boiler service plus a system water test and inhibitor top-up.
- Landlord gas safety check plus a service of the same appliances on the same visit.
- Bathroom refit plus replacing the old isolation valves and checking the cylinder or combi capacity for the new shower.
- Breakdown repair plus a discounted first-year service plan for the same boiler.
A useful test for any bundle: would you recommend it to your own parents? If not, drop it.
Additional work found on the job
Engineers regularly find faults beyond the one they were called for: a weeping valve, a corroded flue, a cylinder with a failing immersion. Handled well, this is good for the customer and for job value. Handled badly, it is how complaints start. Home maintenance and repair already carries a median consumer detriment of £109 per problem[5]; you do not want to add to that figure.
Finish what you were asked to do
Complete or make safe the original job first, so the customer is never left with a choice between paying more and having no heating.
Show and explain
Show the fault, take a photo and explain what happens if it is left. Avoid alarming language unless there is a real safety risk.
Price it in writing
Give a written price on the spot or by message the same day. Where no price is agreed, the Consumer Rights Act 2015 says the consumer must pay a reasonable price[1], which is an argument waiting to happen; an agreed price avoids it.
Follow up
If the customer says not now, note it on their record and mention it at the next service. Many say yes later.
Example: lifting the repair average without upselling
Example: a fictional three-engineer firm in Nottingham has an average repair value of £165. Looking at a quarter's jobs, it finds that 30% of repair visits were under an hour, often for jobs that could have waited, and 12% needed a second visit for parts. Replacement quotes were single-option, with a conversion rate of 34%.
Example changes: a minimum charge covering the first hour and travel, published online; small non-urgent jobs grouped by postcode on two days a week; a winter van stock list agreed with the engineers; and three-option replacement quotes. After two quarters the repair average rises to £198, mainly because fewer visits are short or repeated, and replacement conversion rises to 41%, with most customers choosing the middle option.
Example lesson: nothing in the change involved persuading anyone to buy something they did not need. The value came from pricing visits properly, sending the right parts and giving customers clear choices.
Grants, finance and big-ticket work
For heat pump installers, grants shape job value. The Boiler Upgrade Scheme gives £7,500 towards an air source or ground source heat pump in England and Wales[6], which customers often see as a discount on the whole project. Quote the full installed price, show the grant as a separate line and explain who claims it, so nobody is surprised when the paperwork arrives.
If you offer finance through a third party, check that the lender and your firm have the right permissions and follow their disclosure rules. Never present finance as the way to make an expensive option affordable unless the customer has asked how they could spread the cost.
Measuring the change
- Average value by work type, each month, against the same month last year.
- Share of visits under one hour.
- Second-visit rate for repairs.
- Quote conversion by option chosen.
- Complaints and callbacks, to confirm that higher value has not come at the cost of trust.
Put these on the monthly business review page, and read them alongside revenue per engineer so higher job values are not hiding longer days. If callers keep asking for prices before they will book, our guide to handling the price question on the phone has scripts.
Frequently asked questions
How do I calculate average job value?
Divide turnover by the number of jobs for the period, but do it separately for repairs, servicing, replacements and project work. A single overall figure moves with the work mix and hides real changes.
Is offering several options on a quote pressure selling?
No, as long as each option is a genuine recommendation and the differences are explained plainly. Customers generally prefer choosing between clear options to receiving one take-it-or-leave-it price.
Can an engineer do extra work found on the day?
Yes, once the customer has agreed a price. For contracts made off premises, cancellation rights apply, so work within the 14 days only starts on the customer's express request, recorded in writing.
Should we set a minimum charge?
Most firms should. A minimum that covers travel and the first hour stops small visits losing money and is easy to explain if it is published before the customer books.
References
legislation.gov.uk (The National Archives) (2015). Consumer Rights Act 2015, section 51 (opens in a new tab) ↑
legislation.gov.uk (The National Archives) (2013). The Consumer Contracts (Information, Cancellation and Additional Charges) Regulations 2013, regulation 30 (opens in a new tab) ↑
legislation.gov.uk (The National Archives) (2013). The Consumer Contracts (Information, Cancellation and Additional Charges) Regulations 2013, regulation 36 (opens in a new tab) ↑
Department for Energy Security and Net Zero (2026). Boiler Upgrade Scheme (BUS) monthly statistics: England and Wales, September 2026 (opens in a new tab) ↑
Department for Business, Energy and Industrial Strategy (GOV.UK) (2021). Consumer protection study 2022: understanding the impacts and resolution of consumer problems (opens in a new tab) ↑
GOV.UK (2026). Apply for the Boiler Upgrade Scheme: what you can get (opens in a new tab) ↑